Nissan Altima L32. Instruction — part 1551
WCS-70
< ECU DIAGNOSIS >
COMBINATION METER
ABNIA0679GB
WCS
COMBINATION METER
WCS-71
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Fail Safe
INFOID:0000000004501316
The combination meter performs a fail-safe operation for the functions listed below when communication is
lost.
ABNIA0684GB
WCS-72
< ECU DIAGNOSIS >
COMBINATION METER
DTC Index
INFOID:0000000004501317
NOTE:
“TIME” indicates the following.
• 0: Indicates that a malfunction is detected at present.
• 1-63: Indicates that a malfunction was detected in the past. (Displays number of ignition switch OFF
→ ON
cycles after malfunction is detected. Self-diagnosis result is erased when “63” is exceeded.)
Function
Specifications
Speedometer
Zero indication.
Tachometer
Fuel gauge
Engine coolant temperature gauge
Illumination control
Meter illumination
Change to nighttime mode when communication is lost.
Segment LCD
Odometer
Freeze current indication.
CVT position
Display turns off.
Buzzer
Buzzer turns off.
Warning lamp/indicator lamp
ABS warning lamp
Lamp turns on when communication is lost.
Brake warning lamp
TCS/VDC OFF indicator lamp
SLIP indicator lamp
A/T CHECK warning lamp
Lamp turns off when communication is lost.
Oil pressure warning lamp
Malfunction indicator lamp
Master warning lamp
Air bag warning lamp
High beam indicator
Turn signal indicator lamp
Intelligent Key system warning lamp
Driver and passenger seat belt warn-
ing lamp
Lamp turns off when disconnected.
Charge warning lamp
Security indicator lamp
Low tire pressure warning lamp
Lamp will flash every second for 1 minute and then stay on con-
tinuously thereafter.
CONSULT-III display
Malfunction
Reference
page
CAN COMM CIRC
[U1000]
Malfunction is detected in CAN communication.
CAUTION:
Even when there is no malfunction on CAN communication system, malfunction may be
misinterpreted when battery has low voltage (when maintaining 7 - 8 V for about 2 sec-
onds) or 10A fuse [No. 19, located in the fuse block (J/B)] is disconnected.
VEHICLE SPEED
CIRC
[B2205]
Malfunction is detected when an erroneous speed signal is input.
CAUTION:
Even when there is no malfunction on speed signal system, malfunction may be misin-
terpreted when battery has low voltage (when maintaining 7 - 8 V for about 2 seconds).
WCS
BCM (BODY CONTROL MODULE)
WCS-73
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
BCM (BODY CONTROL MODULE)
Reference Value
INFOID:0000000004501318
VALUES ON THE DIAGNOSIS TOOL
Monitor Item
Condition
Value/Status
FR WIPER HI
Other than front wiper switch HI
OFF
Front wiper switch HI
ON
FR WIPER LOW
Other than front wiper switch LO
OFF
Front wiper switch LO
ON
FR WASHER SW
Front washer switch OFF
OFF
Front washer switch ON
ON
FR WIPER INT
Other than front wiper switch INT
OFF
Front wiper switch INT
ON
FR WIPER STOP
Front wiper is not in STOP position
OFF
Front wiper is in STOP position
ON
INT VOLUME
Wiper intermittent dial is in a dial position 1 - 7
Wiper intermittent dial position
TURN SIGNAL R
Other than turn signal switch RH
OFF
Turn signal switch RH
ON
TURN SIGNAL L
Other than turn signal switch LH
OFF
Turn signal switch LH
ON
TAIL LAMP SW
Other than lighting switch 1ST and 2ND
OFF
Lighting switch 1ST or 2ND
ON
HI BEAM SW
Other than lighting switch HI
OFF
Lighting switch HI
ON
HEAD LAMP SW 1
Other than lighting switch 2ND
OFF
Lighting switch 2ND
ON
HEAD LAMP SW 2
Other than lighting switch 2ND
OFF
Lighting switch 2ND
ON
PASSING SW
Other than lighting switch PASS
OFF
Lighting switch PASS
ON
AUTO LIGHT SW
Other than lighting switch AUTO
OFF
Lighting switch AUTO
ON
FR FOG SW
Front fog lamp switch OFF
OFF
Front fog lamp switch ON
ON
DOOR SW-DR
Driver door closed
OFF
Driver door opened
ON
DOOR SW-AS
Passenger door closed
OFF
Passenger door opened
ON
DOOR SW-RR
Rear door RH closed
OFF
Rear door RH opened
ON
DOOR SW-RL
Rear door LH closed
OFF
Rear door LH opened
ON
DOOR SW-BK
NOTE:
This item is displayed, but cannot be monitored.
OFF
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст