Nissan Altima L32. Instruction — part 648
EM-128
< ON-VEHICLE MAINTENANCE >
[VQ35DE]
COMPRESSION PRESSURE
COMPRESSION PRESSURE
On-Vehicle Service
INFOID:0000000004202157
CHECKING COMPRESSION PRESSURE
1. Run the engine until it reaches normal operating temperature.
2. Turn the ignition switch to OFF.
3. Release fuel pressure and leave the fuel pump electrically disconnected.
4. Remove all six spark plugs.
EM-119, "Removal and Installation"
5. Attach a compression tester to No. 1 cylinder.
6. Depress accelerator pedal fully to keep the electric throttle con-
trol actuator butterfly-valve wide open to maximize air intake
flow.
7. Crank the engine and record the highest gauge indication.
8. Repeat the measurement on each cylinder (steps 5 - 7).
• Always use a fully-charged battery to obtain specified
engine speed.
Unit: kPa (kg/cm
2
, psi)/rpm
9. If compression in one or more cylinders is low:
a. Pour a small amount of engine oil into cylinders through the spark plug holes.
b. Retest compression (steps 5 - 8).
• If adding oil helps raise compression pressure, then the piston rings may be worn or damaged. If so,
replace piston rings after checking piston.
• If the pressure stays low, a valve may be sticking or is seating improperly. Inspect and repair the
valve and/or valve seat. Refer to
. If the valve and/or valve seat is damaged
excessively, replace as necessary.
• If compression stays low in two or more cylinders that are next to each other:
- The cylinder head gasket may be leaking.
- Both cylinders may have valve component damage. Inspect and repair as necessary.
Standard
Minimum
Difference limit between
cylinders
1,275 (13.0, 185)/300
981 (10.0, 142)/300
98 (1.0, 14)/300
SEM387C
AIR CLEANER AND AIR DUCT
EM-129
< ON-VEHICLE REPAIR >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
ON-VEHICLE REPAIR
AIR CLEANER AND AIR DUCT
Removal and Installation
INFOID:0000000004202158
REMOVAL
1. Remove front air duct.
2. Disconnect the tube clamp at the electric throttle control actuator and at the air duct hose.
3. Remove air duct hose.
4. Disconnect mass air flow sensor.
5. Remove mass air flow sensor from air cleaner assembly, as necessary.
CAUTION:
Handle mass air flow sensor with care.
• Do not shock it.
• Do not disassemble it.
• Do not touch its sensor.
6. Remove air cleaner assembly.
INSTALLATION
Installation is in the reverse order of removal.
ALBIA0497ZZ
1.
Air duct hose
2.
Duct sub-cover
3.
Front air duct
4.
Air cleaner assembly
5.
Grommets
6.
Air cleaner mounting bracket
7.
Bracket
8.
Mass air flow sensor
A. To electric throttle control actuator
EM-130
< ON-VEHICLE REPAIR >
[VQ35DE]
INTAKE MANIFOLD COLLECTOR
INTAKE MANIFOLD COLLECTOR
Removal and Installation
INFOID:0000000004202159
REMOVAL
WARNING:
• To avoid the danger of being scalded, never drain the coolant when the engine is hot.
• The gasket for intake manifold collector (upper) is secured together with intake manifold collector
(lower) bolt. Thus, when replacing only the upper gasket the lower gasket must also be replaced.
1. Release fuel pressure. Refer to
.
2. Remove the cowl top. Refer to
EXT-18, "Removal and Installation"
.
3. Remove the engine cover, using power tool.
4. Remove air cleaner assembly and fresh air intake tube as an assembly. Refer to
.
5. Partially drain the coolant when the engine is cool. Refer to
CO-35, "Changing Engine Coolant"
AWBIA0428GB
1.
Power valve (RH)
2.
Intake manifold collector
3.
Gasket
4.
Power valve (LH)
5.
Electric throttle control actuator
INTAKE MANIFOLD COLLECTOR
EM-131
< ON-VEHICLE REPAIR >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
6. If necessary, remove the electric throttle control actuator bolts in
the reverse order as shown and remove the electric throttle con-
trol actuator.
CAUTION:
• Handle carefully to avoid any shock to the electric throttle
control actuator.
• Do not disassemble.
7. If necessary, remove power valve bolts in the reverse order as
shown and remove the power valves.
8. Disconnect the following:
• Power brake booster vacuum hose
• Coolant hoses from the electric throttle control actuator
• Fuel injector electrical connectors
• PCV hose
• Electric throttle control actuator electrical connector
• EVAP canister purge hose
CAUTION:
• Cover any engine openings to avoid the entry of any foreign material.
9. Remove the EVAP canister purge volume solenoid valve bracket bolt. Position the valve aside.
10. Loosen the intake manifold collector bolts in the order as shown
using power tool, and remove the intake manifold collector and
gasket.
11. If necessary remove the following components:
• VIAS control solenoid valve
SEM711G
ALBIA0229ZZ
ALBIA0230ZZ
ALBIA0228ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст