Nissan Altima L32. Instruction — part 1478
TM-256
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
CONTROL CABLE
CONTROL CABLE
Exploded View
INFOID:0000000004201805
Removal and Installation
INFOID:0000000004201806
REMOVAL
1. Shift control lever to "P".
2. Remove the air filter assembly. Refer to
EM-25, "Removal and Installation"
3. Remove the control cable nut and control cable from the instruction lever.
4. Remove the lock plate and the control cable from the bracket.
5. Remove the center console. Refer to
IP-18, "Disassembly and Assembly"
.
6. Remove the bracket covering the retainer grommet.
7. Remove the retainer grommet bolts and the retainer grommet.
8. Remove the control cable from the control device assembly.
9. Remove the control cable from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
• When installing the control cable to the control device assembly, make sure that the control cable socket is
fully pressed into the control device assembly, and the control cable end is fully pressed in with the ribbed
surface facing upward.
• After installation is complete, adjust and check the CVT position. Refer to
TM-253, "Inspection and Adjust-
.
1.
Control lever
2.
Control device assembly
3.
Control cable socket
4.
Retainer grommet
5.
Control cable
6.
Bracket
7.
Lock plate
8.
Instruction lever
ALDIA0026GB
AIR BREATHER HOSE
TM-257
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
Exploded View
INFOID:0000000004201807
Removal and Installation
INFOID:0000000004201808
CAUTION:
• Install air breather hose with paint mark facing front.
• Insert air breather hose onto air breather tube until overlap area reaches the spool.
• Install air breather hose to heater pipe and air cleaner case by fully inserting the clip.
• Make sure there are no pinched or restricted areas on air breather hose caused by bending or wind-
ing when installing it.
1.
Air cleaner
2.
Air breather hose
3.
Transaxle assembly
4.
Heater pipe
5.
Clip
A.
Paint mark
⇐: Front
ALDIA0035ZZ
TM-258
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
DIFFERENTIAL SIDE OIL SEAL
DIFFERENTIAL SIDE OIL SEAL
Exploded View
INFOID:0000000004201809
Removal and Installation
INFOID:0000000004201810
REMOVAL
1. Remove drive shaft assembly. Refer to
and
FAX-12, "Removal and Installation
.
2. Remove the differential side oil seal using suitable tool
CAUTION:
Do not scratch transaxle case or converter housing.
INSTALLATION
1. Drive the new differential side oil seal into the transaxle case
side (B) and converter housing side (C) until it is flush using
Tools.
CAUTION:
• Do not reuse differential side oil seals.
• Apply specified NISSAN CVT fluid to side oil seals.
2. Install drive shaft assembly. Refer to
FAX-11, "Removal and Installation (Left Side)"
"Removal and Installation (Right Side)"
.
3. Check CVT fluid level. Refer to
1.
Transaxle assembly
2.
Differential side oil seal
:NISSAN CVT Fluid NS-2
WCIA0605E
SCIA2412E
Tool number
: — (J-47244) (LH)
: ST33400001 (J-47005) (RH)
Dimension A
: 0
± 0.5 mm (0 ± 0.02 in)
WCIA0598E
TRANSAXLE ASSEMBLY
TM-259
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
Exploded View
INFOID:0000000004201811
Removal and Installation
INFOID:0000000004201812
REMOVAL
1. Remove the engine and transaxle as an assembly. Refer to
EM-72, "Removal and Installation"
NOTE:
Using paint, put matching marks on the drive plate and torque converter when removing the torque con-
verter to drive plate nuts.
2. Disconnect the electrical connectors from the following:
• CVT unit harness connector. Refer to
TM-234, "Removal and Installation Procedure for CVT Unit Con-
• Secondary speed sensor
1.
Rear gusset
2. Air breather hose
3. CVT fluid level gauge
4.
CVT fluid charging pipe
5. O-ring
6. Copper washer
7.
Fluid cooler tube
8. Transaxle assembly
.
ALDIA0036GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст