Nissan Altima L32. Instruction — part 1491
TM-308
< COMPONENT DIAGNOSIS >
[CVT: RE0F10A]
P0705 PARK/NEUTRAL POSITION SWITCH
• Ignition switch
2.
CHECK HARNESS BETWEEN TCM AND PNP SWITCH (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check continuity between TCM harness connector F16 (A) ter-
minal 1, 2, 3, 4, 11 and PNP switch harness connector F25 (B)
terminal 5, 6, 7, 8, 4.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK HARNESS BETWEEN TCM AND PNP SWITCH (PART 2)
Check continuity between TCM harness connector F16 terminal 1, 2,
3, 4, 11 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK CVT POSITION
1. Remove control cable from instruction lever. Refer to
.
2. Check continuity PNP switch connector terminals. Refer to
TM-308, "Component Inspection (Park/Neutral
Is the inspection result normal?
YES
>> Adjust CVT position. Refer to
TM-429, "Inspection and Adjustment"
.
NO
>> GO TO 5.
5.
DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
NO
>> Repair or replace damaged parts.
Component Inspection (Park/Neutral Position Switch)
INFOID:0000000004201875
1.
CHECK PNP SWITCH
1. Adjust PNP switch position. Refer to
TM-429, "Inspection and Adjustment"
TCM harness connector
PNP switch harness connector
Continuity
Connector
Terminal
Connector
Terminal
F16 (A)
1
F25 (B)
5
Existed
2
6
3
7
4
8
11
4
AWDIA0169ZZ
TCM harness connector
Ground
Continuity
Connector
Terminal
F16
1
Not existed
2
3
4
11
AWDIA0093ZZ
P0705 PARK/NEUTRAL POSITION SWITCH
TM-309
< COMPONENT DIAGNOSIS >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2. Check continuity between PNP switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace PNP switch. Refer to
PNP switch terminal
Condition
Continuity
1
2
Instruction lever in “P” position
Existed
3
4
3
5
Instruction lever in “R” position
1
2
Instruction lever in “N” position
3
6
3
7
Instruction lever in “D” position
3
8
Instruction lever in “L” position
JPDIA0987GB
TM-310
< COMPONENT DIAGNOSIS >
[CVT: RE0F10A]
P0710 CVT FLUID TEMPERATURE SENSOR
P0710 CVT FLUID TEMPERATURE SENSOR
Description
INFOID:0000000004201876
The CVT fluid temperature sensor detects the CVT fluid temperature and sends a signal to the TCM.
DTC Logic
INFOID:0000000004201877
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.
CHECK DTC DETECTION (PART 1)
With CONSULT-III
1. Turn ignition switch ON.
2. Select “DATA MONITOR”.
3. Check that output voltage of CVT fluid temperature sensor is within the range specified below.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO-1 (“ATF TEMP SEN” indicates 0.15 or less.)>>Refer to
.
NO-2 (“ATF TEMP SEN” indicates 2.04 or more.)>>GO TO 2.
2.
CHECK DTC DETECTION (PART 2)
With CONSULT-III
1. Turn ignition switch ON.
2. Select “DATA MONITOR”.
3. Start engine and maintain the following conditions for at least 14 minutes.
With GST
Follow the procedure “With CONSULT-III”.
Is “P0710 ATF TEMP SEN/CIRC” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000004201878
1.
CHECK CVT FLUID TEMPERATURE SENSOR CIRCUIT
DTC
Item
(CONSULT-III screen term)
Malfunction is detected when...
Possible cause
P0710
ATF TEMP SEN/CIRC
During running, the CVT fluid temperature
sensor signal voltage is excessively high or
low.
• Harness or connectors
(Sensor circuit is open or shorted.)
• CVT fluid temperature sensor
ATF TEMP SEN
: 0.16 – 2.03 V
RANGE
: “D” position
VEHICLE SPEED
: 10 km/h (6 MPH) or more
P0710 CVT FLUID TEMPERATURE SENSOR
TM-311
< COMPONENT DIAGNOSIS >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check resistance between TCM harness connector F16 terminal
13, 25.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK HARNESS BETWEEN TCM AND CVT UNIT (CVT TEMPERATURE SENSOR) (PART 1)
1. Disconnect CVT unit connector.
2. Check continuity between TCM harness connector F16 (A) ter-
minal 13, 25 and CVT unit harness connector F46 (B) terminal
17, 19.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK HARNESS BETWEEN TCM AND CVT UNIT (CVT TEMPERATURE SENSOR) (PART 2)
Check continuity between TCM harness connector F16 terminal 13,
25 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK CVT FLUID TEMPERATURE SENSOR
Check CVT fluid temperature sensor. Refer to
TM-312, "Component Inspection (CVT Fluid Temperature Sen-
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
CHECK DTC
With CONSULT-III
1. Turn ignition switch ON.
2. Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”.
Is only “P0710 ATF TEMP SEN/CIRC” detected?
YES
>> Replace control valve. Refer to
NO
>> Replace transaxle assembly. Refer to
TM-447, "Removal and Installation"
.
6.
DETECT MALFUNCTIONING ITEMS
TCM harness connector
Temperature
°C (°F)
Resistance
(Approx.)
Connector
Terminal
F16
13
25
20 (68)
6.5 k
Ω
80 (176)
0.9 k
Ω
AWDIA0095ZZ
TCM harness connector
CVT unit harness connector
Continuity
Connector
Terminal
Connector
Terminal
F16 (A)
13
F46 (B)
17
Existed
25
19
AWDIA0096ZZ
TCM harness connector
Ground
Continuity
Connector
Terminal
F16
13
Not existed
25
AWDIA0097ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст