Nissan Altima L32. Instruction — part 435
P0550 PSP SENSOR
EC-861
< COMPONENT DIAGNOSIS >
[QR25DE EXCEPT FOR CALIFORNIA]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
4. Check the voltage between ECM harness connector and ground
under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace power steering pressure sensor.
ECM
Condition
Voltage
Connector
Terminal
F13
41
(Power steering pres-
sure sensor signal)
Steering
wheel
Being turned.
0.5 - 4.5V
Not being
turned.
0.4 - 0.8V
JMBIA1597ZZ
EC-862
< COMPONENT DIAGNOSIS >
[QR25DE EXCEPT FOR CALIFORNIA]
P0603 ECM POWER SUPPLY
P0603 ECM POWER SUPPLY
Description
INFOID:0000000004349825
Battery voltage is supplied to the ECM even when the ignition switch
is turned OFF for the ECM memory function of the DTC memory, the
air-fuel ratio feedback compensation value memory, the idle air vol-
ume learning value memory, etc.
DTC Logic
INFOID:0000000004349826
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON and wait at least 1 second.
2. Start engine and let it idle for 1 second.
3. Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
4. Repeat steps 2 and 3 for four times.
5. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000004349827
1.
CHECK ECM POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
PBIA9222J
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0603
ECM power supply cir-
cuit
ECM back-up RAM system does not function
properly.
• Harness or connectors
[ECM power supply (back-up) circuit is
open or shorted.]
• ECM
P0603 ECM POWER SUPPLY
EC-863
< COMPONENT DIAGNOSIS >
[QR25DE EXCEPT FOR CALIFORNIA]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
3. Check the voltage between ECM harness connector and
ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
• 15A fuse (No. 42)
• IPDM E/R harness connector F10
• Harness for open or short between ECM and battery
>> Repair or replace harness or connectors.
3.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT-III
1. Turn ignition switch ON.
2. Select “SELF-DIAG RESULTS” mode with CONSULT-III.
3. Touch “ERASE”.
4. Perform DTC CONFIRMATION PROCEDURE.
.
With GST
1. Turn ignition switch ON.
2. Select Service $04 with GST.
3. Perform DTC CONFIRMATION PROCEDURE.
.
Is the 1st trip DTC P0603 displayed again?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE ECM
1. Replace ECM.
2. Go to
EC-563, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
.
>> INSPECTION END
ECM
Ground
Voltage
Connector
Terminal
F13
77
Ground
Battery voltage
JMBIA1598ZZ
EC-864
< COMPONENT DIAGNOSIS >
[QR25DE EXCEPT FOR CALIFORNIA]
P0605 ECM
P0605 ECM
Description
INFOID:0000000004349828
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM controls the engine.
DTC Logic
INFOID:0000000004349829
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A
1. Turn ignition switch ON.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B
1. wait at least 1 second.
2. Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
3. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C
1. wait at least 1 second.
2. Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
3. Repeat step 2 for 32 times.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
PBIA9222J
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0605
Engine control module
A)
ECM calculation function is malfunctioning.
• ECM
B)
ECM EEP-ROM system is malfunctioning.
C)
ECM self shut-off function is malfunctioning.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст