Nissan Altima L32. Instruction — part 1203
SE-22
< ON-VEHICLE REPAIR >
[COUPE]
FRONT SEAT
PASSENGER'S SEAT
13. Power seat outer finisher
14. Seat switch assembly
15. Seat slide switch
16. Seat reclining switch
17. Recline lever finisher
18. Instruction seat recline lever
19. Instruction seat outer lower finisher
20. Instruction seat outer finisher
21. Instruction slide cover
22. Power rear leg covers
23. Entry knob
24. Bezel
1.
Headrest
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Seatback board
5.
Rear leg covers
6.
Clip harness
7.
Outer finisher
8.
Seatback lever
9.
Power seat harness
10. Seatback/frame assembly
11. Front leg covers
12. Seat cushion assembly
ALIIA0240GB
FRONT SEAT
SE-23
< ON-VEHICLE REPAIR >
[COUPE]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Removal and Installation
INFOID:0000000004206791
REMOVAL
CAUTION:
• Before removing the front seat, turn the ignition switch off, disconnect both battery terminals and
wait and least 3 minutes.
• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-
tor with the side air bag module connector. Such an error may cause the air bag to deploy.
• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
• After front side air bag module inflates, front seatback assembly must be replaced.
• Always replace passenger seat cushion as an assembly with Occupant Classification System.
• When removing or installing the seat trim, handle it carefully to keep dirt out and avoid damage.
• When removing and installing, use shop cloths to protect the parts from damage where they may
interfere with other parts.
1. Slide the seat until the four seat bolts are visible and a tool can be inserted.
2. Disconnect the negative and positive battery terminals and wait at least 3 minutes.
3. Disconnect the harness connector for the side air bag module.
4. Disconnect the power seat harness connector and vehicle harness clip from the vehicle.
5. Remove the seat leg covers.
6. Remove the four seat bolts.
INSTALLATION
Installation is in the reverse order of removal.
• When installing the LH front seats tighten the bolts as shown.
• When installing the RH front seats tighten the bolts as shown.
13. SRS seat harness
14. Inner finisher
15. Seat belt buckle
16. Release handle
17. Release handle cover
18. Kick lever
LIIA2853E
LIIA2854E
SE-24
< ON-VEHICLE REPAIR >
[COUPE]
REAR SEAT
REAR SEAT
Exploded View
INFOID:0000000004206792
SPLIT REAR SEAT
1.
Release strap
2.
Rear seat lock assembly
3.
Rear striker assembly
4.
Rear seatback reinforcement
5.
LH seatback frame
6.
RH seatback frame
7.
RH seatback pad
8.
LH seatback pad
9.
RH seatback trim
10. LH seatback trim
11. RH seatback hinge assembly
12. Seat cushion trim
13. Seat cushion pad
14. LH seatback hinge assembly
ALIIA0215GB
REAR SEAT
SE-25
< ON-VEHICLE REPAIR >
[COUPE]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Removal and Installation
INFOID:0000000004206793
REMOVAL
1. Remove the rear seat cushion trim and pad.
• Pull the seat cushion upward to release the wire from the plastic hook, then pull the seat cushion for-
ward to remove.
2. Remove the seat belt webbing from the guides.
3. Remove the seatback hinge anchor bolts and nut.
4. Remove the seatback assemblies.
INSTALLATION
Installation is in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст