Nissan Altima L32. Instruction — part 1473
TM-236
< PRECAUTION >
[CVT: RE0F09B]
PRECAUTIONS
• Before connecting or disconnecting the TCM harness connec-
tor, turn ignition switch OFF and disconnect negative battery
cable. Because battery voltage is applied to TCM even if igni-
tion switch is turned OFF.
• When connecting or disconnecting pin connectors into or
from TCM, take care not to damage pin terminals (bend or
break).
When connecting pin connectors make sure that there are not
any bends or breaks on TCM pin terminal.
• Before replacing TCM, perform TCM input/output signal
inspection and make sure whether TCM functions properly or
.
• After performing each TROUBLE DIAGNOSIS, perform “DTC
Confirmation Procedure”.
If the repair is completed the DTC should not be displayed in
the “DTC Confirmation Procedure”.
• Always use the specified brand of CVT fluid. Refer to
• Use lint-free paper, not cloth rags, during work.
• After replacing the CVT fluid, dispose of the waste oil using the
methods prescribed by law, ordinance, etc.
Service Notice or Precaution
INFOID:0000000004201787
CVT FLUID COOLER SERVICE
If CVT fluid contains friction material (clutches, brakes, etc.), or if a CVT is replaced, inspect and clean the
CVT fluid cooler mounted in the radiator or replace the radiator. Flush cooler lines using cleaning solvent and
compressed air after repair. For CVT fluid cooler cleaning procedure, refer to
. For radiator
replacement, refer to
CO-38, "Removal and Installation"
.
OBD-II SELF-DIAGNOSIS
SEF289H
SEF291H
MEF040DA
SEF217U
PRECAUTIONS
TM-237
< PRECAUTION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• CVT self-diagnosis is performed by the TCM in combination with the ECM. The results can be read through
the blinking pattern of the malfunction indicator lamp (MIL). Refer to the table on
for the indicator used to display each self-diagnostic result.
• The self-diagnostic results indicated by the MIL are automatically stored in both the ECM and TCM memo-
ries.
Always perform the procedure on
TM-117, "Diagnosis Description"
to complete the repair and avoid
unnecessary blinking of the MIL.
For details of OBD-II, refer to
TM-117, "Diagnosis Description"
.
• Certain systems and components, especially those related to OBD, may use the new style slide-lock-
ing type harness connector. For description and how to disconnect, refer to
(Coupe) or
ATFTEMP COUNT Conversion Table
INFOID:0000000004201788
ATFTEMP COUNT
Temperature
°C (°F)
ATFTEMP COUNT
Temperature
°C (°F)
4
–30 (–22)
177
90 (194)
8
–20 (–4)
183
95 (203)
13
–10 (14)
190
100 (212)
17
–5 (23)
196
105 (221)
21
0 (32)
201
110 (230)
27
5 (41)
206
115 (239)
32
10 (50)
210
120 (248)
39
15 (59)
214
125 (257)
47
20 (68)
218
130 (266)
55
25 (77)
221
135 (275)
64
30 (86)
224
140 (284)
73
35 (95)
227
145 (293)
83
40 (104)
229
150 (302)
93
45 (113)
231
155 (311)
104
50 (122)
233
160 (320)
114
55 (131)
235
165 (329)
124
60 (140)
236
170 (338)
134
65 (149)
238
175 (347)
143
70 (158)
239
180 (356)
152
75 (167)
241
190 (374)
161
80 (176)
243
200 (392)
169
85 (185)
—
—
TM-238
< PREPARATION >
[CVT: RE0F09B]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000004201789
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000004201790
Tool number
(Kent-Moore No.)
Tool name
Description
—
(OTC3492)
Oil pressure gauge set
Measuring line pressure
—
(J-47244)
Drift
Installing differential side oil seal
• Transaxle case side (left)
a: 65.83 mm (2.59 in) dia.
b: 53.85 mm (2.12 in) dia.
ST33400001
(J-47005)
Drift
Installing differential side oil seal
• Converter housing side (right)
a: 69.85 mm (2.75 in) dia.
b: 49.53 mm (1.95 in) dia.
SCIA7531E
SCIA5777E
SCIA5777E
Tool number
Tool name
Description
31197CA000
Drive plate location guide
Installing transaxle assembly
a: 14 mm (0.55 in) dia.
31093CA000
Slinger
Removing and installing transaxle assembly
SCIA2013E
SCIA2014E
PREPARATION
TM-239
< PREPARATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
31092CA000
Slinger
Removing and installing transaxle assembly
Power tool
Loosening nuts and bolts
Tool number
Tool name
Description
SCIA2015E
PBIC0190E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст