Nissan Altima L32. Instruction — part 189
CL-10
< ON-VEHICLE REPAIR >
CLUTCH MASTER CYLINDER
CLUTCH MASTER CYLINDER
Removal and Installation
INFOID:0000000004499033
REMOVAL
1. Remove the air cleaner and air duct. Refer to
EM-19, "Removal and Installation"
123, "Removal and Installation"
for VQ35DE.
2. Use one of the following methods to remove hose from master cylinder.
• Drain clutch fluid from reservoir tank and remove hose.
• Remove hose from master cylinder. Immediately plug hose and reservoir tank to prevent clutch fluid
from dripping.
CAUTION:
Do not spill clutch fluid onto painted surfaces. If it spills, wipe up immediately and wash the
affected area with water.
3. Remove master cylinder rod end from clutch pedal assembly.
4. Remove lock pin (1) from connector of master cylinder (2) and
separate clutch tube (3).
5. Rotate master cylinder clockwise by 45
° and remove from the vehicle.
INSTALLATION
1. Tilt master cylinder clockwise by 45
° and insert it in the mounting
hole. Rotate counterclockwise to secure it. At this time, nipple is
in the up position.
2. Install master cylinder rod end to clutch pedal.
PCIB1491E
PCIB1497E
SCIA1286E
CLUTCH MASTER CYLINDER
CL-11
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
3. Install clutch tube (1) fully into connector of master cylinder (2).
4. Install lock pin (3) fully into connector of master cylinder (2).
5. Fill with new clutch fluid and bleed clutch hydraulic system.
CL-6, "Inspection and Adjustment"
.
6. Inspect clutch pedal operation. Refer to
.
7. Install the air cleaner and air duct. Refer to
for VQ35DE.
PCIB1500E
CL-12
< ON-VEHICLE REPAIR >
CLUTCH PIPING
CLUTCH PIPING
Exploded View
INFOID:0000000004499034
Removal and Installation
INFOID:0000000004499035
CAUTION:
Do not spill clutch fluid onto painted surfaces. If it spills, wipe up immediately and wash the affected
area with water.
REMOVAL
1. Remove the air cleaner and air duct. Refer to
EM-19, "Removal and Installation"
123, "Removal and Installation"
for VQ35DE.
2. Remove the lock pin and disconnect the clutch master cylinder connector.
3. Remove the clutch tubes from the branch connector.
4. Remove the clutch tube and air bleed connector valve.
5. Remove the branch connector.
6. Remove lock pin and disconnect the CSC connector.
INSTALLATION
Installation is in the reverse order of removal.
• Make sure that all tubes are fully installed into connectors.
• Make sure that all connector lock pins are fully installed.
• After installation, bleed clutch hydraulic system. Refer to
CL-7, "Air Bleeding Procedure"
.
1.
Clutch tube
2.
CSC connector
3.
Lock pin
4.
CSC
5.
Air bleed connector valve
6.
Clutch pedal
7.
Clutch master cylinder
8.
Clutch master cylinder connector
9.
Branch connector
ALDIA0017ZZ
CSC (CONCENTRIC SLAVE CYLINDER)
CL-13
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
REMOVAL AND INSTALLATION
CSC (CONCENTRIC SLAVE CYLINDER)
Exploded View
INFOID:0000000004499036
Removal and Installation
INFOID:0000000004499037
CAUTION:
• If transaxle assembly is removed from the vehicle, always replace CSC. Return CSC insert to original
position to remove transaxle assembly. Dust on clutch disc sliding parts may damage CSC seal and
may cause clutch fluid leakage.
• Do not spill clutch fluid onto painted surfaces. If it spills, wipe up immediately and wash the affected
area with water.
REMOVAL
1. Remove the transaxle assembly. Refer to
TM-26, "Removal and Installation"
.
2. Remove CSC bolts and CSC from clutch housing.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse CSC.
• Do not insert and operate CSC because piston and stopper of CSC components may fall off.
After installation, bleed clutch hydraulic system. Refer to
CL-7, "Air Bleeding Procedure"
.
1.
Transaxle assembly
2.
CSC (Concentric Slave Cylinder)
JPDIB0040GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст