Nissan Altima L32. Instruction — part 1581
ROAD WHEEL TIRE ASSEMBLY
WT-67
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
c. If calculated balance weight value exceeds 50 g (1.76 oz.),
install two balance weight sheets in line with each other as
shown.
CAUTION:
Do not install one balance weight sheet on top of another.
5. Start wheel balancer again.
6. Install drive-in balance weight on inner side of road wheel in the
wheel balancer indication position (angle).
CAUTION:
Do not install more than two balance weights.
7. Start wheel balancer. Make sure that inner and outer residual
unbalance values are 5 g (0.18 oz.) each or below.
• If either residual unbalance value exceeds 5 g (0.18 oz.), repeat installation procedures.
Wheel balance (Maximum allowable unbalance):
TIRE ROTATION
• Follow the maintenance schedule for tire rotation service intervals. Refer to
.
• Do not include the T-type spare tire when rotating the tires.
CAUTION:
• When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
• Be careful not to tighten wheel nut at torque exceeding the
criteria for preventing strain of disc rotor.
Maximum allowable un-
balance
Dynamic (At rim flange)
5 g (0.18 oz.) (one side)
Static
10 g (0.35 oz.)
SMA056D
Tightening torque of
wheel nut
: 113 N·m (12 kg-m, 83 ft-lb)
SMA829C
WT-68
< REMOVAL AND INSTALLATION >
TRANSMITTER
REMOVAL AND INSTALLATION
TRANSMITTER
Removal and Installation
INFOID:0000000004205329
REMOVAL
1. Remove wheel and tire using power tool.
2. Deflate tire. Unscrew transmitter retaining nut and allow transmitter to fall into tire.
3. Gently bounce tire so that transmitter falls to bottom of tire.
Place wheel and tire assembly on tire changing machine and
break both tire beads. Ensure that the transmitter remains at the
bottom of the tire while breaking the bead.
4. Turn tire so that valve hole is at bottom, and gently bounce the
tire to ensure transmitter is near valve hole. Carefully lift tire onto
turntable and position valve hole (and transmitter) 270 degrees
from mounting/dismounting head.
5. Lubricate tire well, and remove top side of tire. Reach inside the
tire and remove the transmitter.
6. Remove the second side of the tire as normal.
INSTALLATION
1. Place first side of tire onto rim.
2. Apply suitable silicone lubricant to new transmitter seal then install seal on transmitter. Refer to
.
NOTE:
Always replace the seal after every disassembly.
SEIA0047E
WEIA0046E
SEIA0049E
TRANSMITTER
WT-69
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
3. Mount transmitter on rim and tighten nut at a maximum speed of
10 rpm.
NOTE:
Make sure no burrs exist in the valve stem hole of the wheel.
4. Place wheel on turntable of tire machine. Ensure that transmitter
is 270 degrees from mounting/dismounting head.
NOTE:
Do not touch transmitter with mounting head.
5. Lubricate tire well, and install second side of tire as normal.
Ensure that tire does not rotate relative to rim.
6. Inflate tire and balance the wheel and tire assembly. Refer to
7. Install wheel and tire assembly in appropriate wheel position on
vehicle. Refer to
.
NOTE:
If replacing the transmitter, then transmitter wake up operation
must be performed. Refer to
WT-5, "Transmitter Wake Up Operation"
8. Adjust neutral position of steering angle sensor. Refer to
BRC-143, "ADJUSTMENT OF STEERING
ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
Transmitter nut
tightening torque
: 7.7 N·m (0.79 kg-m, 68 in-lb)
WEIA0137E
WEIA0046E
WT-70
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Road Wheel
INFOID:0000000004205330
Tire
INFOID:0000000004205331
Unit: kPa (kg/cm
2
, psi)
Standard item
Allowable value
Aluminum
Steel
Maximum radial
runout limit
Lateral deflection
Less than 0.3 mm (0.012 in) Less than 1.5 mm (0.059 in)
Radial deflection
Less than 0.3 mm (0.012 in) Less than 1.5 mm (0.059 in)
Maximum allowable
unbalance
Dynamic
(At rim flange)
Less than 5 g (0.18 oz) (one side)
Static
(At rim flange)
Less than 10 g (0.35 oz)
Tire size
Air pressure
Front tire
Rear tire
P215/60R16
220 (2.2, 32)
220 (2.2, 32)
P215/55R17
230 (2.3, 33)
230 (2.3, 33)
P235/45R18
230 (2.3, 33)
230 (2.3, 33)
T135/70R16
420 (4.2, 60)
420 (4.2, 60)
T135/90D16
420 (4.2, 60)
420 (4.2, 60)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст