Nissan Altima L32. Instruction — part 818

HAC-46

< COMPONENT DIAGNOSIS >

[AUTOMATIC AIR CONDITIONER]

MAGNET CLUTCH

MAGNET CLUTCH

Description

INFOID:0000000004498212

SYSTEM DESCRIPTION

Front air control controls A/C compressor operation by ambient temperature and signal from ECM.

Low Temperature Protection Control

Front air control will turn the A/C compressor ON or OFF as deter-

mined by a signal detected by ambient sensor.

When ambient temperature is greater than -2

°C (28°F), the A/C

compressor turns ON. The A/C compressor turns OFF when ambi-

ent temperature is less than -5

°C (23°F).

Component Function Check

INFOID:0000000004498213

INSPECTION FLOW

1.

CONFIRM SYMPTOM BY PERFORMING OPERATION CHECK - MAGNET CLUTCH

1. Press ignition switch ON.
2. Press vent switch (

).

3. Press A/C switch.

4. Confirm that the A/C compressor clutch engages (sound or visual inspection). (Discharge air and blower

speed will depend on ambient, in-vehicle and set temperatures).

Can a symptom be duplicated?

YES

>> GO TO 3

NO

>> GO TO 2

2.

PERFORM COMPLETE OPERATIONAL CHECK

Perform a complete operational check and check for any symptoms. Refer to

HAC-5, "Description and Condi-

tions"

.

Is the inspection result normal?

YES

>> Refer to

HAC-83, "Symptom Matrix Chart"

.

NO

>> System OK.

3.

CHECK FOR SERVICE BULLETINS

Check for any service bulletins.

>> GO TO 4

4.

CHECK MAGNET CLUTCH MECHANISM

Check for magnet clutch operation.
Does the magnet clutch engage?

YES

>> GO TO 5

NO

>> Check magnet clutch circuit. Refer to

HAC-47, "Diagnosis Procedure"

.

5.

CHECK AMBIENT SENSOR CIRCUIT

Perform diagnostic procedure for the mode door motor. Refer to

HAC-32, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 6

NO

>> Repair as necessary.

RHA094GB

MAGNET CLUTCH

HAC-47

< COMPONENT DIAGNOSIS >

[AUTOMATIC AIR CONDITIONER]

C

D

E

F

G

H

J

K

L

M

A

B

HAC

N

O

P

6.

CHECK IN-VEHICLE SENSOR CIRCUIT

Perform diagnostic procedure for the in-vehicle sensor circuit. Refer to

HAC-53, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 7

NO

>> Repair as necessary.

7.

CHECK SUNLOAD SENSOR CIRCUIT

Perform diagnostic procedure for the sunload sensor circuit. Refer to

HAC-56, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 8

NO

>> Repair as necessary.

8.

CHECK INTAKE SENSOR CIRCUIT

Perform diagnostic procedure for the intake sensor circuit. Refer to

HAC-59, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 9

NO

>> Repair as necessary.

9.

CHECK AIR MIX DOOR MOTOR PBR CIRCUITS

Perform diagnostic procedure for the air mix door motor circuit. Refer to

HAC-35, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 10

NO

>> Repair as necessary.

10.

RECHECK FOR SYMPTOMS

Perform a complete operational check and check for any symptoms. Refer to

HAC-5, "Description and Condi-

tions"

.

Does another symptom exist?

YES

>> Repair as necessary.

NO

>> Replace front air control. Refer to

VTL-8, "Removal and Installation"

.

Diagnosis Procedure

INFOID:0000000004498214

DIAGNOSIS PROCEDURE FOR MAGNET CLUTCH

SYMPTOM: Magnet clutch does not engage when A/C switch is ON.

AWIIA0029GB

HAC-48

< COMPONENT DIAGNOSIS >

[AUTOMATIC AIR CONDITIONER]

MAGNET CLUTCH

1.

CHECK POWER SUPPLY FOR A/C COMPRESSOR

1. Disconnect A/C compressor connector.

2. Start engine and press A/C switch.

3. Check voltage between A/C compressor harness connector F3

terminal 1 and ground.

Is the inspection result normal?

YES

>>

Check magnet clutch coil.

1. If NG, replace magnet clutch. Refer to

HA-35, "Removal and Installation for Compressor -

QR25DE Models"

or

HA-36, "Removal and Installation for Compressor - VQ35DE Models"

.

2. If OK, check A/C compressor mounting points for looseness or corrosion and repair as neces-

sary.

NO

>> GO TO 2

2.

CHECK CIRCUIT CONTINUITY BETWEEN A/C RELAY IN IPDM E/R AND A/C COMPRESSOR

1. Disconnect IPDM E/R connector F10 and A/C compressor con-

nector F3.

2. Check continuity between A/C compressor harness connector

F3 (A) terminal 1 and IPDM E/R harness connector F10 (B) ter-

minal 48.

If OK, check harness for short to ground.
Is the inspection result normal?

YES

>> GO TO 3

NO

>> Repair harness or connector.

3.

CHECK FUSE IN IPDM E/R

Check 10A fuse (No. 41 located in the IPDM E/R).
Is the inspection result normal?

YES

>> GO TO 4

NO

>> Replace fuse and check IPDM E/R for short circuit. Replace if necessary.

4.

CHECK A/C COMPRESSOR ON SIGNAL

Check voltage between front air control connector M37 terminal 5

and ground, with A/C compressor ON and with A/C compressor

OFF.

Is the inspection result normal?

YES

>> GO TO 5

NO

>> • When A/C compressor is ON and voltage is not approx. 0V, Replace front air control. Refer to

VTL-8, "Removal and Installation"

.

Terminal

Voltage (V)

(Approx.)

(+)

(-)

Connector - Terminal

Body ground

12V

F3-1

AWIIA0621ZZ

Terminals

Continuity

Connector - Terminal

Connector - Terminal

Yes

F3 - 1

F10 - 48

AWIIA0622ZZ

Terminal

Voltage (V)

(Approx.)

(+)

(-)

Connector - Terminal

Body ground

A/C compressor ON: 0V

A/C compressor OFF:

5V

M37 - 5

AWIIA0623ZZ

MAGNET CLUTCH

HAC-49

< COMPONENT DIAGNOSIS >

[AUTOMATIC AIR CONDITIONER]

C

D

E

F

G

H

J

K

L

M

A

B

HAC

N

O

P

• When A/C compressor is OFF and voltage is not approx. 5V, BCM is malfunctioning.

5.

CHECK CONTINUITY BETWEEN BCM AND FRONT AIR CONTROL

1. Disconnect BCM connector M18 and front air control connector.

2. Check continuity between BCM harness connector M18 (A) ter-

minal 33 and front air control connector M37 (B) terminal 5.

Is the inspection result normal?

YES

>> GO TO 6

NO

>> Repair harness or connector.

6.

CHECK REFRIGERANT PRESSURE SENSOR INPUT SIGNAL

1. Reconnect all disconnected connectors.

2. Start the engine.

3. Check voltage between ECM harness connector F13 terminal

39 and ground.

Is the inspection result normal?

YES

>> GO TO 7

NO

>> 1. Repair harness or connector.

2. Confirm that magnet clutch operation is normal.

7.

CHECK REFRIGERANT PRESSURE SENSOR

Refer to

EC-975, "Diagnosis Procedure"

(QR25DE) or

EC-1503, "Diagnosis Procedure"

(VQ35DE).

Is the inspection result normal?

YES

>> GO TO 8

NO

>> Replace refrigerant pressure sensor. Refer to

HA-44, "Removal and Installation for Refrigerant

Pressure Sensor"

.

8.

CHECK CAN COMMUNICATION CIRCUITS

Check CAN communication circuits between BCM to ECM and between ECM to IPDM E/R. Refer to

LAN-13,

"CAN Diagnosis with CONSULT-III"

.

Is the inspection result normal?

YES

>> ECM malfunctioning.

NO

>> Repair or replace component based on the result of diagnosis.

Terminals

Continuity

Connector - Terminal

Connector - Terminal

M18 - 33

M37 - 5

Yes

AWIIA0624ZZ

Terminal

Voltage (V)

(Approx.)

(+)

(-)

Connector- Terminal

Body ground

12V

F13-39

AWIIA0625ZZ