Nissan Altima L32. Instruction — part 690
EXL-44
< COMPONENT DIAGNOSIS >
HEADLAMP (LO) CIRCUIT
1. Select "EXTERNAL LAMP" of IPDM E/R active test item.
2. With operating the test items, check that the headlamp is turned ON.
Is the headlamp turned ON?
YES
>> Headlamp (LO) is normal.
NO
>> Refer to
EXL-44, "HEADLAMP (XENON) : Diagnosis Procedure"
HEADLAMP (XENON) : Diagnosis Procedure
INFOID:0000000004201497
1.
CHECK HEADLAMP (LO) FUSES
1. Turn the ignition switch OFF.
2. Check that the following fuses are not open.
Is the fuse open?
YES
>> Repair the harness and replace the fuse.
NO
>> GO TO 2
2.
CHECK HEADLAMP (LO) OUTPUT VOLTAGE
CONSULT-III
1. Turn the ignition switch OFF.
2. Disconnect the front combination lamp connector.
3. Turn the ignition switch ON.
4. Select "EXTERNAL LAMP" of IPDM E/R active test item.
5. With EXTERNAL LAMP ON, check the voltage between the
combination lamp connector and ground.
Is battery voltage present?
YES
>> GO TO 4
NO
>> GO TO 3
3.
CHECK HEADLAMP (LO) CIRCUIT FOR OPEN
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and
the front combination lamp harness connector.
Does continuity exist?
YES
>> GO TO 4
NO
>> Repair the harnesses or connectors.
LO
: Headlamp ON
OFF
: Headlamp OFF
Unit
Location
Fuse No.
Capacity
Headlamp LO (LH)
IPDM E/R
51
15A
Headlamp LO (RH)
IPDM E/R
52
15A
(+)
(
−)
Voltage
Connector
Terminal
RH
E223
1
Ground
Battery voltage
LH
E212
1
AWLIA0568ZZ
A
B
Continuity
Connector
Terminal
Connector
Terminal
RH
E200
83
E223
1
Yes
LH
84
E212
1
AWLIA0569ZZ
HEADLAMP (LO) CIRCUIT
EXL-45
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
4.
CHECK FRONT COMBINATION LAMP (LO) GROUND CIRCUIT
1. Disconnect the front combination lamp connector.
2. Check continuity between the front combination lamp harness
connector terminal and ground.
Does continuity exist?
YES
>> Inspect the headlamp bulb.
NO
>> Repair the harness.
Connector
Terminal
—
Continuity
RH
E223
2
Ground
Yes
LH
E212
2
AWLIA0570ZZ
EXL-46
< COMPONENT DIAGNOSIS >
FRONT FOG LAMP CIRCUIT
FRONT FOG LAMP CIRCUIT
Description
INFOID:0000000004201498
The IPDM E/R (intelligent power distribution module engine room) controls the front fog lamp relay based on
inputs from the BCM over the CAN communication lines. When the front fog lamp relay is energized, power
flows from the front fog lamp relay in the IPDM E/R to the front fog lamps.
Component Function Check
INFOID:0000000004201499
1.
CHECK FRONT FOG LAMP OPERATION
WITHOUT CONSULT-III
1. Activate IPDM E/R auto active test. Refer to
PCS-14, "Diagnosis Description"
2. Check that the front fog lamp is turned ON.
CONSULT-III
1. Select "EXTERNAL LAMP" of IPDM E/R active test item.
2. With operating the test items, Check that the front fog lamp is turned ON.
Is the front fog lamp turned ON?
YES
>> Front fog lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000004201500
1.
CHECK FRONT FOG LAMP FUSE
1. Turn the ignition switch OFF.
2. Check that the following fuses are not open.
Is the fuse open?
YES
>> Repair the harness and replace the fuse.
NO
>> GO TO 2
2.
CHECK FRONT FOG LAMP OUTPUT VOLTAGE
CONSULT-III
1. Turn the ignition switch OFF.
2. Disconnect the front fog lamp connector.
3. Turn the ignition switch ON.
4. Select "EXTERNAL LAMP" of IPDM E/R active test item.
5. With EXTERNAL LAMP ON, check the voltage between the fog
lamp connector and ground.
Is battery voltage present?
YES
>> GO TO 4
NO
>> GO TO 3
3.
CHECK FRONT FOG LAMP OPEN CIRCUIT
1. Turn the ignition switch OFF.
FOG
: Front fog lamp ON
OFF
: Front fog lamp OFF
Unit
Location
Fuse No.
Capacity
Front fog lamp
IPDM E/R
53
15A
(+)
(
−)
Voltage
Connector
Terminal
LH
E214
1
Ground
Battery voltage
RH
E227
1
ALLIA0119ZZ
FRONT FOG LAMP CIRCUIT
EXL-47
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and
the front fog lamp harness connector.
Does continuity exist?
YES
>> GO TO 4
NO
>> Repair the harnesses or connectors.
4.
CHECK FRONT FOG LAMP GROUND CIRCUIT
1. Disconnect the front fog lamp connector.
2. Check continuity between the front fog lamp harness connector
terminal and ground.
Does continuity exist?
YES
>> Inspect the fog lamp bulb.
NO
>> Repair the harness.
A
B
Continuity
Connector
Terminal
Connector
Terminal
RH
E200
86
E227
1
Yes
LH
87
E214
1
ALLIA0123ZZ
Connector
Terminal
—
Continuity
RH
E227
2
Ground
Yes
LH
E214
2
ALLIA0121ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст