Nissan Altima L32. Instruction — part 1452
TM-152
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
P0776 PRESSURE CONTROL SOLENOID B PERFORMANCE (SEC PRESSURE
SOLENOID VALVE)
P0776 PRESSURE CONTROL SOLENOID B PERFORMANCE (SEC PRES-
SURE SOLENOID VALVE)
Description
INFOID:0000000004201711
The pressure control solenoid valve B (secondary pressure solenoid valve) regulates the secondary pressure
to suit the driving condition in response to a signal sent from the TCM.
DTC Logic
INFOID:0000000004201712
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.
CHECK DTC DETECTION
With CONSULT-III
1. Turn ignition switch ON.
2. Select “DATA MONITOR”.
3. Start engine and maintain the following conditions for at least 30 consecutive seconds.
With GST
Follow the procedure “With CONSULT-III”.
Is “P0776 PRS CNT SOL/B FCTN” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000004201713
1.
CHECK LINE PRESSURE
Perform line pressure test. Refer to
TM-247, "Inspection and Judgment"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts. Refer to
TM-247, "Inspection and Judgment"
.
2.
CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
1. Turn ignition switch OFF.
2. Disconnect CVT unit harness connector.
DTC
Item
(CONSULT-III screen term)
Malfunction is detected when...
Possible cause
P0776
PRS CNT SOL/B FCTN
Secondary pressure is too high or too low
compared with the commanded value while
driving.
• Harness or connectors
(Solenoid circuit is open or shorted.)
• Pressure control solenoid valve B (sec-
ondary pressure solenoid valve system)
• Transmission fluid pressure sensor A
(secondary pressure sensor)
• Line pressure control system
ATF TEMP SEN
: 1.0
− 2.0 V
ACC PEDAL OPEN
: More than 1.0/8
RANGE
: “D” position
VEHICLE SPEED
: 10 km/h (6 MPH) or more
Driving location
: Driving the vehicle uphill (increased engine load) will help maintain the driving
conditions required for this test.
P0776 PRESSURE CONTROL SOLENOID B PERFORMANCE (SEC PRESSURE
SOLENOID VALVE)
TM-153
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3. Check pressure control solenoid valve B (secondary pressure solenoid valve). Refer to
nent Inspection [Pressure Control Solenoid Valve B (Secondary Pressure Solenoid Valve)]"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace transaxle assembly. Refer to
3.
CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)
Check pressure control solenoid valve A (line pressure solenoid valve). Refer to
tion [Pressure Control Solenoid Valve A (Line Pressure Solenoid Valve)]"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace transaxle assembly. Refer to
4.
CHECK TRANSMISSION FLUID PRESSURE SENSOR A (SECONDARY PRESSURE SENSOR) SYS-
TEM
Check transmission fluid pressure sensor A (secondary pressure sensor) system. Refer to
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace damaged parts.
5.
DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
NO
>> Repair or replace damaged parts.
Component Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid
Valve)]
INFOID:0000000004201714
1.
CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)
Check resistance between CVT unit terminal 2 and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace transaxle assembly. Refer to
Component Inspection [Pressure Control Solenoid Valve B (Secondary Pressure So-
lenoid Valve)]
INFOID:0000000004201715
1.
CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
CVT unit terminal
Ground
Resistance (Approx.)
2
3.0 – 9.0
Ω
AWDIA0122ZZ
TM-154
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
P0776 PRESSURE CONTROL SOLENOID B PERFORMANCE (SEC PRESSURE
SOLENOID VALVE)
Check resistance between CVT unit terminal 3 and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace transaxle assembly. Refer to
.
CVT unit terminal
Ground
Resistance (Approx.)
3
3.0 – 9.0
Ω
AWDIA0123ZZ
P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRESSURE
SOLENOID VALVE)
TM-155
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRES-
SURE SOLENOID VALVE)
Description
INFOID:0000000004201716
The pressure control solenoid valve B (secondary pressure solenoid valve) regulates the oil pump discharge
pressure to suit the driving condition in response to a signal sent from the TCM.
DTC Logic
INFOID:0000000004201717
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.
CHECK DTC DETECTION
With CONSULT-III
1. Start engine.
2. Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.
3. Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is “P0778 PRS CNT SOL/B CIRC” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000004201718
1.
CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect TCM harness connector.
3. Check resistance between TCM harness connector F16 terminal
39 and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK HARNESS BETWEEN TCM AND PRESSURE CONTROL SOLENOID VALVE B (SECONDARY
PRESSURE SOLENOID VALVE) (PART 1)
DTC
Item
(CONSULT-III screen term)
Malfunction is detected when...
Possible cause
P0778
PRS CNT SOL/B CIRC
• Normal voltage not applied to solenoid
due to cut line, short, or the like.
• TCM detects as irregular by comparing
target value with monitor value.
• Harness or connectors
(Solenoid circuit is open or shorted.)
• Pressure control solenoid valve B (sec-
ondary pressure solenoid valve)
TCM harness connector
Ground
Resistance (Ap-
prox.)
Connector
Terminal
F16
39
3.0 – 9.0
Ω
AWDIA0124ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст