Nissan Altima L32. Instruction — part 1210
SE-50
< ON-VEHICLE REPAIR >
[SEDAN]
FRONT SEAT
PASSENGER'S SEAT
13. Seat cushion frame
14. Instruction seat lifter lever finisher
15. Instruction seat recliner handle
16. Instruction seat lifter lever
17. Instruction seat outer finisher
18. Seat slide switch
19. Seat reclining switch
20. Power seat outer finisher
21. Seat switch assembly
22. LH seat bracket
23. Front seat finisher
24. Cushion bracket
25. Inner seat cover
26. Seat frame assembly
27. Cushion finishers
28. Rear leg covers
ALIIA0272GB
FRONT SEAT
SE-51
< ON-VEHICLE REPAIR >
[SEDAN]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Removal and Installation
INFOID:0000000004206809
REMOVAL
CAUTION:
• Before removing the front seat, turn the ignition switch off, disconnect both battery terminals and
wait and least 3 minutes.
• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-
tor with the side air bag module connector. Such an error may cause the air bag to deploy.
• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
• After front side air bag module inflates, front seatback assembly must be replaced.
• Always replace passenger seat cushion as an assembly with Occupant Classification System.
• When removing or installing the seat trim, handle it carefully to keep dirt out and avoid damage.
• When removing and installing, use shop cloths to protect the parts from damage where they may
interfere with other parts.
1. Slide the seat until the four seat bolts are visible and a tool can be inserted.
2. Disconnect the negative and positive battery terminals and wait at least 3 minutes.
3. Disconnect the harness connector for the side air bag module.
4. Disconnect the power seat harness connector and vehicle harness clip from the vehicle.
5. Remove the seat leg covers.
6. Remove the four seat bolts.
INSTALLATION
Installation is in the reverse order of removal.
• When installing the LH front seats tighten the bolts as shown.
• When installing the RH front seats tighten the bolts as shown.
1.
Headrest
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Seatback board
5.
Seatback assembly
6.
Seat cushion assembly
7.
Bushing
8.
Seat cushion frame assembly
9.
Front leg covers
10. Cushion bracket
11. Seat frame assembly
12. Seat harness
13. Seat belt buckle
14. Inner finisher
15. Outer finisher
16. Seat cushion supporter
17. Recliner mechanism
18. Finisher
19. Cushion finishers
20. Rear leg covers
LIIA2853E
LIIA2854E
SE-52
< ON-VEHICLE REPAIR >
[SEDAN]
REAR SEAT
REAR SEAT
Exploded View
INFOID:0000000004206810
BENCH SEAT
1.
Rear seat side bolster assembly LH 2.
Rear seatback latch mount
3.
Rear seat side bolster assembly RH
4.
Rear seatback latch
5.
Rear seatback trim panel
6.
Seat belt guide
7.
Rear seatback pad RH
8.
Rear seatback pad LH
9.
Rear seatback pad trim RH
10. Rear seatback pad trim LH
11. Armrest
12. Armrest trim panel
ALIIA0028GB
REAR SEAT
SE-53
< ON-VEHICLE REPAIR >
[SEDAN]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Removal and Installation
INFOID:0000000004206811
REMOVAL
1. Remove the rear seat cushion trim and pad.
• Pull the lock at the front bottom of the seat cushion forward
(one for each side), and pull the seat cushion upward to
release the wire from the plastic hook, then pull the seat cush-
ion forward to remove.
2. Remove the seat belt webbing from the guides.
3. Fold seatbacks forward.
4. Remove upper seatback trim panel.
5. Remove rear side bolster bolts.
6. Lock seatbacks in upright position.
7. Remove the seatback hinge anchor bolts and nut.
8. Remove the seatback assembly.
INSTALLATION
Installation is in the reverse order of removal.
13. Cup holder
14. Rear seatback hinge assembly
15. Rear seat cushion trim
16. Rear seat cushion
SIIA0511E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст