Nissan Altima L32. Instruction — part 929
MA-30
< ON-VEHICLE MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
6. Pull out the CVT fluid level gauge from the CVT fluid charging
pipe after pressing the tab on the CVT fluid level gauge to
release the lock.
7. Wipe fluid off the CVT fluid level gauge. Insert the CVT fluid
level gauge rotating 180
° from the originally installed position,
then securely push the CVT fluid level gauge until it meets the
top end of the CVT fluid charging pipe.
CAUTION:
When wiping away the CVT fluid level gauge, always use
lint-free paper, not a cloth rag.
8. Place the selector lever in “P” or “N” and make sure the fluid
level is within the specified range.
CAUTION:
When reinstalling CVT fluid level gauge, insert it into the
CVT fluid charging pipe and rotate it to the original installa-
tion position until it is securely locked.
CVT FLUID CONDITION
Check CVT fluid condition.
• If CVT fluid is very dark or smells burned, check operation of CVT.
Flush cooling system after repair of CVT.
• If CVT fluid contains frictional material (clutches, brakes, etc.),
replace radiator and flush cooler line using cleaning solvent and
compressed air after repair of CVT. Refer to
.
SCIA1933E
SCIA1931E
SCIA1932E
Fluid status
Conceivable cause
Required operation
Varnished (viscous
varnish state)
Clutch, brake
scorched
Replace the CVT fluid and check the
CVT main unit and the vehicle for
malfunctions (wire harnesses, cool-
er pipes, etc.)
Milky white or
cloudy
Water in the fluid
Replace the CVT fluid and check for
places where water is getting in.
Large amount of
metal powder mixed
in
Unusual wear of
sliding parts within
CVT
Replace the CVT fluid and check for
improper operation of the CVT.
ATA0022D
CHASSIS AND BODY MAINTENANCE
MA-31
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
CVT FLUID : Changing
INFOID:0000000004523233
1. Warm up CVT fluid by driving the vehicle for 10 minutes.
•
: Vehicle front
• Radiator (2)
• CVT fluid cooler hose (inlet side) (3)
• Transaxle assembly (4)
2. Drain CVT fluid from CVT fluid cooler hose (outlet side) (1) and
refill with new CVT fluid at CVT fluid charging pipe with the
engine running at idle speed.
3. Refill until new CVT fluid comes out from CVT fluid cooler hose
(outlet side) (1).
About 30 to 50% extra fluid will be required for this procedure.
CAUTION:
• Use only Genuine NISSAN CVT Fluid NS-2. Do not mix with other fluid.
• Using CVT fluid other than Genuine NISSAN CVT Fluid NS-2 will deteriorate in driveability and
CVT durability, and may damage the CVT, which is not covered by the warranty.
• When filling CVT fluid, take care not to scatter heat generating parts such as exhaust.
• Delete CVT fluid deterioration date with CONSULT-III after changing CVT fluid. Refer to
"CONSULT-III Function (TRANSMISSION)"
4. Check fluid level and condition. Refer to
.
CVT FLUID : RE0F10A
INFOID:0000000004202069
CVT FLUID : Inspection
INFOID:0000000004202070
CHECKING CVT FLUID
Fluid level should be checked with the fluid warmed up to 50 to 80
°C (122 to 176°F). The fluid level check pro-
cedure is as follows:
1. Check for fluid leakage.
2. With the engine warmed up, drive the vehicle in an urban area.
When ambient temperature is 20
°C (68°F), it takes about 10
minutes for the CVT fluid to warm up to 50 to 80
°C (122 to
176
°F).
3. Park the vehicle on a level surface.
4. Apply parking brake firmly.
5. With engine at idle, while depressing brake pedal, move shift
selector throughout the entire shift range.
6. Pull out the CVT fluid level gauge from the CVT fluid charging
pipe after pressing the tab on the CVT fluid level gauge to
release the lock.
CVT fluid:
TM-261, "General Specification"
.
Fluid capacity:
TM-261, "General Specification"
.
SCIA6088E
SMA146B
SCIA1933E
MA-32
< ON-VEHICLE MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
7. Wipe fluid off the CVT fluid level gauge. Insert the CVT fluid
level gauge rotating 180
° from the originally installed position,
then securely push the CVT fluid level gauge until it meets the
top end of the CVT fluid charging pipe.
CAUTION:
When wiping away the CVT fluid level gauge, always use
lint-free paper, not a cloth rag.
8. Place the selector lever in “P” or “N” and make sure the fluid
level is within the specified range.
CAUTION:
When reinstalling CVT fluid level gauge, insert it into the
CVT fluid charging pipe and rotate it to the original installa-
tion position until it is securely locked.
CVT FLUID CONDITION
Check CVT fluid condition.
• If CVT fluid is very dark or smells burned, check operation of CVT.
Flush cooling system after repair of CVT.
• If CVT fluid contains frictional material (clutches, brakes, etc.),
replace radiator and flush cooler line using cleaning solvent and
compressed air after repair of CVT. Refer to
.
CVT FLUID : Changing CVT Fluid
INFOID:0000000004523234
1. Warm up CVT fluid by driving the vehicle for 10 minutes.
•
: Vehicle front
• Radiator (2)
• CVT fluid cooler hose [inlet side (3)]
• Transaxle assembly (4)
2. Drain CVT fluid from CVT fluid cooler hose [outlet side (1)] and
refill with new specified NISSAN CVT fluid in the CVT fluid
charging pipe with the engine running at idle speed.
3. Refill until new CVT fluid comes out from CVT fluid cooler hose
[outlet side (1)].
NOTE:
About 30 to 50% extra fluid will be required for this procedure.
SCIA1931E
SCIA1932E
Fluid status
Conceivable cause
Required operation
Varnished (viscous
varnish state)
CVT fluid become
degraded due to
high temperatures.
Replace the CVT fluid and check the
CVT main unit and the vehicle for
malfunctions (wire harnesses, cool-
er pipes, etc.)
Milky white or
cloudy
Water in the fluid
Replace the CVT fluid and check for
places where water is getting in.
Large amount of
metal powder mixed
in
Unusual wear of
sliding parts within
CVT
Replace the CVT fluid and check for
improper operation of the CVT.
ATA0022D
SCIA6088E
CHASSIS AND BODY MAINTENANCE
MA-33
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
4. Check fluid level and condition. Refer to
.
CAUTION:
• Use only Genuine NISSAN CVT Fluid NS-2. Never mix with other fluid.
• Using CVT fluid other than Genuine NISSAN CVT Fluid NS-2 will deteriorate in driveability and
CVT durability, and may damage the CVT, which is not covered by the warranty.
• When filling CVT fluid, take care not to scatter heat generating parts such as exhaust.
• Sufficiently shake the container of CVT fluid before using.
• Delete CVT fluid deterioration date with CONSULT-III after changing CVT fluid. Refer to TM-34,
"CONSULT-III Function (TRANSMISSION)".
M/T OIL
M/T OIL : Draining
INFOID:0000000004202072
1. Start engine and let it run to warm up transaxle oil.
2. Stop engine and remove the drain plug to drain the oil.
3. Install the drain plug with a new gasket to the transaxle case. Tighten the drain plug to the specified
.
CAUTION:
Do not reuse gasket.
M/T OIL : Refilling
INFOID:0000000004523235
1. Remove the filler plug (1) and fill transaxle with new oil.
2. After refilling oil, measure oil level to check if it is within the spec-
ification using suitable gauge (A) as shown.
CAUTION:
• Do not start engine while checking oil level.
• Insert the suitable gauge straight and against the wall of
the filler plug hole, then measure the gauge from the top
of the filler plug hole to the oil level as shown.
3. Install the filler plug with a new O-ring to the clutch housing.
CAUTION:
Do not reuse O-ring.
4. Tighten filler plug bolt to the specified torque. Refer to
.
M/T OIL : Inspection
INFOID:0000000004523236
LEAKAGE
• Make sure that oil is not leaking from transaxle or around it.
LEVEL
CVT fluid
: Refer to
TM-451, "General Specification"
Fluid capacity
: Refer to
TM-451, "General Specification"
Oil grade
: Refer to
MA-12, "Fluids and Lubricants"
Oil level “L” : Refer to
TM-82, "General Specifications"
.
JPDIC0138ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст