Nissan Altima L32. Instruction — part 1530
VTL-12
< ON-VEHICLE REPAIR >
HEATER & COOLING UNIT ASSEMBLY
HEATER & COOLING UNIT ASSEMBLY
Removal and Installation
INFOID:0000000004205418
COMPONENTS
REMOVAL
1. Discharge the refrigerant from the A/C system. Refer to
HA-24, "HFC-134a (R-134a) Service Procedure"
2. Drain the engine coolant from the cooling system. Refer to
CO-12, "Changing Engine Coolant"
CO-35, "Changing Engine Coolant"
(VQ35DE).
3. Disconnect the negative battery terminal.
4. Remove the wiper motor and linkage. Refer to
WW-116, "FRONT WIPER DRIVE ASSEMBLY : Removal
5. Remove the upper cowl (for VQ35DE only). Refer to
EXT-18, "Removal and Installation"
.
6. Remove the strut tower bar (for VQ35DE only). Refer to
.
7. Remove the lower RH cowl (for VQ35DE only). Refer to
EXT-18, "Removal and Installation"
8. Disconnect the heater hoses from the heater core pipes.
CAUTION:
Cap or wrap the pipe joint with a suitable material such as vinyl tape to avoid the entry of contam-
inants into the system.
9. Disconnect the refrigerant lines from the expansion valve. Refer to
CAUTION:
Cap or wrap the line joint with a suitable material such as vinyl tape to avoid the entry of contami-
nants into the system.
10. Remove the instrument panel assembly. Refer to
IP-12, "Removal and Installation"
.
11. Remove the steering column assembly. Refer to
ST-14, "Removal and Installation"
12. Disconnect the drain hose.
13. Remove the heater and cooling unit assembly attached to the steering member as one assembly from the
vehicle.
1.
Steering member
2.
Heater and cooling unit
3.
Blower unit
ALIIA0017GB
HEATER & COOLING UNIT ASSEMBLY
VTL-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
14. Remove the blower unit from the heater and cooling unit and steering member assembly.
15. Remove the heater and cooling unit from the steering member.
INSTALLATION
Installation is in the reverse order of removal.
• Fill the radiator with the specified water and coolant mixture. Refer to
MA-12, "Fluids and Lubricants"
.
• Recharge the A/C system. Refer to
HA-24, "HFC-134a (R-134a) Service Procedure"
.
VTL-14
< ON-VEHICLE REPAIR >
BLOWER UNIT
BLOWER UNIT
Removal and Installation
INFOID:0000000004205419
COMPONENTS
REMOVAL
1. Remove the heater and cooling unit assembly. Refer to
VTL-12, "Removal and Installation"
.
2. Disconnect the blower motor connector.
3. Remove the screws from the blower unit, then remove the blower unit.
INSTALLATION
Installation is in the reverse order of removal.
1.
Heater and cooling unit
2.
Blower unit
⇐
Front
ALIIA0013ZZ
BLOWER MOTOR
VTL-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
BLOWER MOTOR
Removal and Installation
INFOID:0000000004205420
REMOVAL
1. Remove the glove box. Refer to
IP-12, "Removal and Installation"
.
2. Disconnect the blower motor connector (1).
3. Remove the three blower motor screws (A) and remove the
blower motor from the blower unit.
INSTALLATION
Installation is in the reverse order of removal.
ALIIA0014ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст