Nissan Altima L32. Instruction — part 840
HAC-134
< COMPONENT DIAGNOSIS >
[MANUAL AIR CONDITIONER]
MAGNET CLUTCH
8.
CHECK CAN COMMUNICATION CIRCUITS
Check CAN communication circuits between BCM to ECM and between ECM to IPDM E/R. Refer to
"CAN Diagnosis with CONSULT-III"
Is the inspection result normal?
YES
>> ECM malfunctioning.
NO
>> Repair or replace component based on the result of diagnosis.
POWER SUPPLY AND GROUND CIRCUIT FOR FRONT AIR CONTROL
HAC-135
< COMPONENT DIAGNOSIS >
[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
POWER SUPPLY AND GROUND CIRCUIT FOR FRONT AIR CONTROL
Description
INFOID:0000000004498280
COMPONENT DESCRIPTION
FRONT AIR CONTROL
The front air control has a built-in microcomputer which processes
information sent from temperature control dial and various switches
needed for air conditioner operation. The air mix door motor, mode
door motor, intake door motor, blower motor and compressor are
then controlled.
POTENTIO TEMPERATURE CONTROL (PTC)
The PTC is built into the front air control.
Component Function Check
INFOID:0000000004498281
COMPONENT INSPECTION
SYMPTOM: A/C system does not come on.
INSPECTION FLOW
1.
CONFIRM SYMPTOM BY PERFORMING OPERATION CHECK
1. Press A/C switch (indicator should illuminate).
2. Confirm that the compressor clutch engages (sound or visual inspection).
Can a symptom be duplicated?
YES
>> GO TO 3
NO
>> GO TO 2
2.
PERFORM COMPLETE OPERATIONAL CHECK
Perform a complete operational check and check for any symptoms. Refer to
.
Is the inspection result normal?
YES
>> Refer to
HAC-155, "Symptom Matrix Chart"
NO
>> System OK.
3.
CHECK FOR SERVICE BULLETINS
Check for any service bulletins.
>> GO TO 4
4.
CHECK MAIN POWER SUPPLY AND GROUND CIRCUIT
Check main power supply and ground circuit. Refer to
HAC-135, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> Replace front air control. Refer to
VTL-8, "Removal and Installation"
.
NO
>> Repair as necessary.
Diagnosis Procedure
INFOID:0000000004498282
DIAGNOSIS PROCEDURE FOR A/C SYSTEM
AWIIA0040ZZ
HAC-136
< COMPONENT DIAGNOSIS >
[MANUAL AIR CONDITIONER]
POWER SUPPLY AND GROUND CIRCUIT FOR FRONT AIR CONTROL
SYMPTOM: A/C system does not come on.
1.
CHECK POWER SUPPLY CIRCUIT FOR FRONT AIR CONTROL
1. Disconnect front air control connector M37.
2. Press ignition switch ON.
3. Check voltage between front air control connector M37 termi-
nals 39 and 40, and ground.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Check the following.
• 10A fuses [Nos. 6, and 3, located in the fuse block (J/B)].
• If fuses are OK, check for open circuit in wiring harness. Repair or replace as necessary.
• If fuses are NG, replace fuse and check wiring harness for short circuit. Repair or replace as
necessary.
2.
CHECK BODY GROUND CIRCUIT FOR FRONT AIR CONTROL
1. Press ignition switch OFF.
2. Check continuity between front air control connector M37 termi-
nals 17and 37 and ground.
Is the inspection result normal?
YES
>> • Replace front air control. Refer to
VTL-8, "Removal and Installation"
.
• Inspection End.
NO
>> Repair or replace harness.
AWIIA0047GB
Terminals
Voltage (V)
(Approx.)
(+)
(-)
Connector - Terminal
Body ground
12V
M37-39
M37-40
AWIIA0635ZZ
Terminal
Continuity
(+)
(-)
Connector - Terminal
Body ground
Yes
M37-17
M37-37
AWIIA0620ZZ
AIR CONDITIONER CONTROL
HAC-137
< ECU DIAGNOSIS >
[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
ECU DIAGNOSIS
AIR CONDITIONER CONTROL
Reference Value
INFOID:0000000004498283
VALUES ON THE DIAGNOSIS TOOL
Display Item List
TERMINAL LAYOUT
PHYSICAL VALUES
Monitor item name
“operation or unit”
Contents
FAN ON SIG
“ON/OFF” Displays “FAN (ON)/FAN (OFF)” status as judged from blower fan motor switch signal.
AIR COND SW
“ON/OFF”
Displays “COMP (ON)/COMP (OFF)” status as judged from air conditioner switch signal.
AWIIA0052ZZ
Termi-
nal No.
Wire
color
Item
Ignition
switch
Condition
Voltage (V)
(Approx.)
1
L/Y
Blower motor feed back
Fan speed
Low
7.0.- 10.0
3
L/R
A/C LAN signal
—
5.5
5
SB
Compressor ON signal
Compressor
ON
0
OFF
12
16
R/L
Light (+)
Lighting
switch
OFF
0
1st position
12
17
B
Ground
—
0
18
W/L
Power supply for IGN
—
12
20
L/W
Power supply for mode door
motor, intake door motor, and
air mix door motor
—
12
21
R/W
Power supply for A/C ON signal
ON
4.6
22
GR
Rear defrost feed back
Defroster
switch
ON
12
OFF
0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст