Nissan Altima L32. Instruction — part 805
HA-40
< ON-VEHICLE REPAIR >
HIGH-PRESSURE PIPE
HIGH-PRESSURE PIPE
Removal and Installation for High-Pressure Pipe
INFOID:0000000004205506
QR25DE
Removal
1. Discharge the refrigerant. Refer to
HA-24, "HFC-134a (R-134a) Service Procedure"
.
2. Remove the strut tower bar. Refer to
3. Remove the upper cowl. Refer to
EXT-18, "Removal and Installation"
4. Remove the lower RH cowl.
5. Reposition the power steering reservoir out of the way without disconnecting the hose.
6. Reposition the engine coolant reservoir out of the way without disconnecting the hose.
7. Remove the high-pressure pipe. Refer to
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
Installation
Installation is in the reverse order of removal.
CAUTION:
• Replace the O-ring of the high-pressure pipe with a new one, then apply compressor oil to it when
installing it.
• After charging the refrigerant, check for leaks. Refer to
HA-25, "Checking of Refrigerant Leaks"
.
VQ35DE
Removal
1. Discharge the refrigerant. Refer to
HA-24, "HFC-134a (R-134a) Service Procedure"
.
2. Remove the strut tower bar. Refer to
3. Remove the upper cowl. Refer to
EXT-18, "Removal and Installation"
4. Remove the lower RH cowl.
5. Disconnect the power steering hose clamp to reposition the power steering hose out of the way.
6. Reposition the power steering reservoir out of the way without disconnecting the hose.
7. Reposition the engine coolant reservoir out of the way without disconnecting the hose.
8. Remove the high-pressure pipe. Refer to
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
Installation
Installation is in the reverse order of removal.
CAUTION:
• Replace the O-ring of the high-pressure pipe with a new one, then apply compressor oil to it when
installing it.
• After charging the refrigerant, check for leaks. Refer to
HA-25, "Checking of Refrigerant Leaks"
.
Removal and Installation for Junction Pipe
INFOID:0000000004205507
REMOVAL
1. Discharge the refrigerant. Refer to
HA-24, "HFC-134a (R-134a) Service Procedure"
.
2. Remove the front grille. Refer to
EXT-17, "Removal and Installation"
3. Remove the junction pipe. Refer to
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
HIGH-PRESSURE PIPE
HA-41
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
• Replace the O-ring of the junction pipe with a new one, then apply compressor oil to it when install-
ing it.
• After charging the refrigerant, check for leaks. Refer to
HA-42
< ON-VEHICLE REPAIR >
CONDENSER
CONDENSER
Removal and Installation for Condenser
INFOID:0000000004205508
REMOVAL
1. Discharge the refrigerant. Refer to
HA-32, "HFC-134a (R-134a) Service Procedure"
.
2. Remove the front fascia (coupe only). Refer to
EXT-17, "Removal and Installation"
.
3. Remove the front grille (sedan only). Refer to
EXT-38, "Removal and Installation"
4. Remove the junction pipe. Refer to
HA-40, "Removal and Installation for Junction Pipe"
.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of con-
taminants.
5. Disconnect the refrigerant pressure sensor connector.
6. Depress the top RH clip (A) and the top LH clip (B) to release
the top condenser brackets as shown.
7. Slide the condenser up to release the condenser from the clips
as shown.
8. Remove the condenser.
CAUTION:
Do not damage the condenser fins
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not damage the condenser fins.
• Replace the O-rings of the junction pipe and refrigerant pressure sensor with new ones, then apply
A/C oil to them after installing them.
• When charging refrigerant, check for leaks. Refer to
HA-25, "Checking of Refrigerant Leaks"
ALIIA0003ZZ
AMBIENT SENSOR
HA-43
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
AMBIENT SENSOR
Removal and Installation
INFOID:0000000004205509
REMOVAL
1. From under the vehicle, disconnect the ambient sensor connec-
tor (2).
2. Release the ambient sensor clip and remove the ambient sen-
sor (1).
INSTALLATION
Installation is in the reverse order of removal.
ALIIA0212ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст