Nissan Altima L32. Instruction — part 1320
SEC-430
< FUNCTION DIAGNOSIS >
[SEDAN WITHOUT INTELLIGENT KEY]
DIAGNOSIS SYSTEM (BCM)
MULTI REMOTE ENT
MULTI REMOTE ENT : CONSULT-III Function (BCM - MULTIREMOTE ENT)
INFOID:0000000004507210
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
Monitor Item
Condition
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-BK
NOTE:
This item is displayed, but cannot be monitored.
CDL LOCK SW
Indicates [ON/OFF] condition of door lock and unlock switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of door lock and unlock switch.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from keyfob.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from keyfob.
RKE-TR/BD
Indicates [ON/OFF] condition of TRUNK OPEN signal from keyfob.
RKE-PANIC
Indicates [ON/OFF] condition of PANIC button of keyfob.
RKE-P/W OPEN
Indicates [ON/OFF] condition of P/W DOWN signal from keyfob.
RKE-MODE CHG
Indicates [ON/OFF] condition of MODE CHANGE signal from keyfob.
KEY CYL LK-SW
Indicated [ON/OFF] condition of lock signal from door key cylinder.
KEY CYL UN-SW
Indicated [ON/OFF] condition of unlock signal from door key cylinder.
KEY CYL SW-TR
NOTE:
This item is displayed, but cannot be monitored.
Test item
Description
INT LAMP
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.
LUGGAGE LAMP TEST
NOTE:
This item is displayed, but cannot be tested.
DOOR LOCK
This test is able to check door lock/unlock operation.
• The all door lock actuators are locked when “ALL LCK” on CONSULT-III screen is touched.
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT-III screen is
touched.
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT-III screen
is touched.
• The door lock actuator (passenger side) is unlocked when “AS UNLK” on CONSULT- III
screen is touched.
• The door lock actuator (rear LH and RH) is unlocked when “OTR ULK” on CONSULT-III
screen is touched.
FLASHER
This test is able to check flasher operation [LH/RH/OFF].
HORN
This test is able to check horn operation [ON/OFF].
TRUNK/GLASS HATCH
This test is able to check trunk lid opener actuator open operation.
This actuator opens when “ON” on CONSULT-III screen is touched.
TRUNK/BACK DOOR
NOTE:
This item is displayed, but cannot be tested.
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be tested.
DIAGNOSIS SYSTEM (BCM)
SEC-431
< FUNCTION DIAGNOSIS >
[SEDAN WITHOUT INTELLIGENT KEY]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
THEFT ALM
THEFT ALM : CONSULT-III Function (BCM - THEFT ALM)
INFOID:0000000004499064
WORK SUPPORT
DATA MONITOR
Test item
Description
DOOR LOCK-UNLOCK SET
Selective unlock function mode can be changed to operate (WITH) or not operate (WITHOUT)
with this mode.
HORN CHIRP SET
Answer back function (horn) mode can be changed in this mode.
For the detail of the setting.
HAZARD LAMP SET
Answer back function (hazard) mode can be changed in this mode.
• MODE1: Non-operation
• MODE2: Lock (non-operation) Unlock (blink once)
• MODE3: Lock (blink towice) Unlock (non-operation)
• MODE4: Lock (blink towice) Unlock (blink once)
AUTO LOCK SET
Auto door lock time can be changed in this mode.
• MODE 1: 1 minute
• MODE 2: 5 minutes
PANIC ALARM SET
Panic alarm button pressing time on keyfob remote control button can be selected from the
following with this mode.
• MODE1: 0.5 sec.
• MODE2: 1.5 sec.
• MODE3: Non-operation
PW DOWN SET
Unlock button pressing time on keyfob button can be selected from the following with this
mode.
• MODE 1: 3 sec.
• MODE 2: Non-operation
• MODE 3: 5 se
Test Item
Description
SECURITY ALARM SET
This mode is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded. This mode is able to confirm and
erase the record of vehicle security alarm. The trigger data can be erased by touching “CLEAR” on
CONSULT-III screen.
Monitored Item
Description
REQ SW -DR
Indicates [ON/OFF] condition of front door request switch (driver side).
REQ SW -AS
Indicates [ON/OFF] condition of front door request switch (passenger side).
REQ SW -RR
Indicates [ON/OFF] condition of rear door request switch (passenger side.
REQ SW -RL
Indicates [ON/OFF] condition of rear door request switch (driver side).
REQ SW -BD/TR
Indicates [ON/OFF] condition of trunk request switch.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch
UNLK SEN -DR
Indicates [ON/OFF] condition of driver door UNLOCK status.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch LH.
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch RH.
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-BK
NOTE:
This is displayed even when it is not equipped.
CDL LOCK SW
Indicates [ON/OFF] condition of lock signal from door lock/unlock switch LH and RH.
SEC-432
< FUNCTION DIAGNOSIS >
[SEDAN WITHOUT INTELLIGENT KEY]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
IMMU
IMMU : CONSULT-III Function (BCM - IMMU)
INFOID:0000000004499065
DATA MONITOR
ACTIVE TEST
CDL UNLOCK SW
Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch LH and RH.
KEY CYL LK-SW
Indicates [ON/OFF] condition of lock signal from front door key cylinder switch.
KEY CYL UN-SW
Indicates [ON/OFF] condition of unlock signal from front door key cylinder switch.
KEY CYL SW-TR
NOTE:
This is displayed even when it is not equipped.
TR/BD OPEN SW
Indicates [ON/OFF] condition of trunk opener switch.
TRNK/HAT MNTR
Indicates [ON/OFF] condition of trunk lid.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
Indicates [ON/OFF] condition of TRUNK OPEN signal from Intelligent Key.
Monitored Item
Description
Test Item
Description
THEFT IND
This test is able to check security indicator lamp operation. The lamp will be turned on when “ON”
on CONSULT-III screen is touched.
VEHICLE SECURITY HORN
This test is able to check vehicle security horn operation. The horns will be activated for 0.5 sec-
onds after “ON” on CONSULT-III screen is touched.
HEADLAMP(HI)
This test is able to check vehicle security lamp operation. The headlamps will be activated for 0.5
seconds after “ON” on CONSULT-III screen is touched.
FLASHER
This test is able to check vehicle security hazard lamp operation. The hazard lamps will be activat-
ed after “ON” on CONSULT-III screen is touched.
Monitor item
Content
CONFRM ID ALL
Indicates [YET] at all time.
Switch to [DONE] when a registered Intelligent Key is inserted into the key slot.
CONFIRM ID4
CONFIRM ID3
CONFIRM ID2
CONFIRM ID1
TP 4
Indicates the number of ID which has been registered.
TP 3
TP 2
TP 1
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
Test Item
Description
THEFT IND
This test is able to check security indicator operation [ON/OFF].
U1000 CAN COMM CIRCUIT
SEC-433
< COMPONENT DIAGNOSIS >
[SEDAN WITHOUT INTELLIGENT KEY]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000004499071
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control unit, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less
wiring. Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart, refer to
LAN-25, "CAN Communication Signal Chart"
DTC Logic
INFOID:0000000004499072
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000004499073
1.
PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Check “Self Diagnostic Result”.
Is “CAN COMM CIRCUIT” displayed?
YES
>> Refer to
LAN-8, "CAN Communication Control Circuit"
.
NO
>> Refer to
GI-42, "Intermittent Incident"
.
CONSULT-III dis-
play description
DTC Detection Condition
Possible cause
CAN COMM CIR-
CUIT
[U1000]
When BCM cannot communicate CAN communication
signal continuously for 2 seconds or more.
In CAN communication system, any item (or items)
of the following listed below is malfunctioning.
• Transmission
• Receiving (ECM)
• Receiving (ABS)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (IPDM E/R)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст