Nissan Altima L32. Instruction — part 517
P0037, P0038, P0057, P0058 HO2S2 HEATER
EC-1189
< COMPONENT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
YES
>> GO TO 5.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
5.
CHECK HEATED OXYGEN SENSOR 2 HEATER
EC-1189, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 6.
6.
REPLACE HEATED OXYGEN SENSOR 2
Replace malfunctioning heated oxygen sensor 2.
CAUTION:
• Discard any heated oxygen sensor which has been dropped from a height of more than 0.5 m (19.7
in) onto a hard surface such as a concrete floor; use a new one.
• Before installing new oxygen sensor, clean exhaust system threads using Oxygen Sensor Thread
Cleaner [commercial service tool (J-43897-18 or J-43897-12)] and approved anti-seize lubricant
(commercial service tool).
>> INSPECTION END
7.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000004362035
1.
CHECK HEATED OXYGEN SENSOR 2 HEATER
Check resistance between HO2S2 terminals as per the following.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
REPLACE HEATED OXYGEN SENSOR 2
Replace malfunctioning heated oxygen sensor 2.
CAUTION:
• Discard any heated oxygen sensor which has been dropped from a height of more than 0.5 m (19.7
in) onto a hard surface such as a concrete floor; use a new one.
Terminal No.
Resistance
2 and 3
3.4 - 4.4
Ω [at 25°C (77°F)]
1 and 2, 3, 4
∞ Ω
(Continuity should not exist)
4 and 1, 2, 3
PBIB3310E
EC-1190
< COMPONENT DIAGNOSIS >
[VQ35DE]
P0037, P0038, P0057, P0058 HO2S2 HEATER
• Before installing new oxygen sensor, clean exhaust system threads using Oxygen Sensor Thread
Cleaner [commercial service tool (J-43897-18 or J-43897-12)] and approved anti-seize lubricant
(commercial service tool).
>> INSPECTION END
P0075, P0081 IVT CONTROL SOLENOID VALVE
EC-1191
< COMPONENT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0075, P0081 IVT CONTROL SOLENOID VALVE
Description
INFOID:0000000004362036
Intake valve timing control solenoid valve is activated by ON/OFF
pulse duty (ratio) signals from the ECM.
The intake valve timing control solenoid valve changes the oil
amount and direction of flow via the intake valve timing control unit
or stops oil flow.
The longer pulse width advances valve timing.
The shorter pulse width retards valve timing.
When ON and OFF pulse widths become equal, the solenoid valve
stops oil pressure flow to fix the intake valve angle at the control
position.
DTC Logic
INFOID:0000000004362037
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for 5 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
EC-1191, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000004362038
1.
CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect intake valve timing (IVT) control solenoid valve harness connector.
3. Turn ignition switch ON.
PBIB1842E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0075
Intake valve timing control so-
lenoid valve (bank 1) circuit
An improper voltage is sent to the ECM via
the intake valve timing control solenoid
valve.
• Harness or connectors
(Intake valve timing control solenoid valve
circuit is open or shorted.)
• Intake valve timing control solenoid valve
P0081
Intake valve timing control so-
lenoid valve (bank 2) circuit
EC-1192
< COMPONENT DIAGNOSIS >
[VQ35DE]
P0075, P0081 IVT CONTROL SOLENOID VALVE
4. Check the voltage between intake valve timing control solenoid
valve harness connector and ground with CONSULT-III or tester.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair open circuit, short to ground or short to power in
harness or connectors.
2.
CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE OUTPUT SIGNAL CIRCUIT FOR OPEN
AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between intake valve timing control solenoid valve harness connector and ECM har-
ness connector.
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
3.
CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE
EC-1192, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace malfunctioning intake valve timing control solenoid valve.
4.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000004362039
1.
CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-I
1. Disconnect intake valve timing control solenoid valve harness connector.
2. Check resistance between intake valve timing control solenoid
valve terminals as per the following.
Is the inspection result normal?
YES
>> GO TO 2.
DTC
IVT control solenoid valve
Ground
Voltage
Bank
Connector
Terminal
P0075
1
F67
2
Ground
Battery voltage
P0081
2
F66
2
PBIB0192E
DTC
IVT control solenoid valve
ECM
Continuity
Bank
Connector
Terminal
Connector
Terminal
P0075
1
F67
1
F13
78
Existed
P0081
2
F66
1
75
Terminals
Resistance
1 and 2
7.0 - 7.5
Ω [at 20°C (68°F)]
1 or 2 and ground
∞ Ω
(Continuity should not exist)
PBIB0193E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст