Nissan Altima L32. Instruction — part 559
P0456 EVAP CONTROL SYSTEM
EC-1357
< COMPONENT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Repair or reconnect the hose.
13.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
EC-1319, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 14.
NO
>> Replace EVAP canister purge volume control solenoid valve.
14.
CHECK FUEL TANK TEMPERATURE SENSOR
EC-1276, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 15.
NO
>> Replace fuel level sensor unit.
15.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-1334, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 16.
NO
>> Replace EVAP control system pressure sensor.
16.
CHECK EVAP PURGE LINE
Check EVAP purge line (pipe, rubber tube, fuel tank and EVAP canister) for cracks or improper connection.
Is the inspection result normal?
YES
>> GO TO 17.
NO
>> Repair or reconnect the hose.
17.
CLEAN EVAP PURGE LINE
Clean EVAP purge line (pipe and rubber tube) using air blower.
>> GO TO 18.
18.
CHECK EVAP/ORVR LINE
Check EVAP/ORVR line between EVAP canister and fuel tank for clogging, kinks, looseness and improper
connection. For location, refer to
.
Is the inspection result normal?
YES
>> GO TO 19.
NO
>> Repair or replace hoses and tubes.
19.
CHECK RECIRCULATION LINE
Check recirculation line between fuel filler tube and fuel tank for clogging, kinks, cracks, looseness and
improper connection.
Is the inspection result normal?
YES
>> GO TO 20.
NO
>> Repair or replace hose, tube or fuel filler tube.
20.
CHECK REFUELING EVAP VAPOR CUT VALVE
EC-1500, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 21.
NO
>> Replace refueling EVAP vapor cut valve with fuel tank.
21.
CHECK FUEL LEVEL SENSOR
MWI-47, "Component Inspection"
.
Is the inspection result normal?
EC-1358
< COMPONENT DIAGNOSIS >
[VQ35DE]
P0456 EVAP CONTROL SYSTEM
YES
>> GO TO 22.
NO
>> Replace fuel level sensor unit.
22.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000004362191
1.
CHECK FUEL FILLER CAP
1. Turn ignition switch OFF.
2. Remove fuel filler cap.
3. Wipe clean valve housing.
4. Install fuel filler cap adapter (commercial service tool) to fuel filler cap.
5. Check valve opening pressure and vacuum.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
REPLACE FUEL FILLER CAP
Replace fuel filler cap.
CAUTION:
Use only a genuine fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the MIL may
illuminate.
>> INSPECTION END
SEF445Y
Pressure: 15.3 - 20.0 kPa (0.156 - 0.204 kg/cm
2
, 2.22 -
2.90 psi)
Vacuum:
−6.0 to −3.3 kPa (−0.061 to −0.034 kg/cm
2
,
−0.87 to −0.48 psi)
SEF943S
P0460 FUEL LEVEL SENSOR
EC-1359
< COMPONENT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0460 FUEL LEVEL SENSOR
Description
INFOID:0000000004362192
The fuel level sensor is mounted in the fuel level sensor unit.
The sensor detects a fuel level in the fuel tank and transmits a signal to the combination meter. The combina-
tion meter sends the fuel level sensor signal to the ECM via the CAN communication line.
It consists of two parts, one is mechanical float and the other is variable resistor. Fuel level sensor output volt-
age changes depending on the movement of the fuel mechanical float.
DTC Logic
INFOID:0000000004362193
DTC DETECTION LOGIC
NOTE:
• If DTC P0460 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.
Refer to
• If DTC P0460 is displayed with DTC P0607, first perform the trouble diagnosis for DTC P0607. Refer
.
When the vehicle is parked, the fuel level in the fuel tank is naturally stable. It means that output signal of the
fuel level sensor does not change. If ECM senses sloshing signal from the sensor, fuel level sensor malfunc-
tion is detected.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and wait maximum of 2 consecutive minutes.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
EC-1359, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000004362194
1.
CHECK COMBINATION METER FUNCTION
MWI-38, "CONSULT-III Function (METER/M&A)"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Go to
.
2.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0460
Fuel level sensor circuit
noise
Even though the vehicle is parked, a signal be-
ing varied is sent from the fuel level sensor to
ECM.
• Harness or connectors
(The CAN communication line is open or
shorted.)
• Harness or connectors
(The sensor circuit is open or shorted.)
• Combination meter
• Fuel level sensor
EC-1360
< COMPONENT DIAGNOSIS >
[VQ35DE]
P0460 FUEL LEVEL SENSOR
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст