Nissan Altima L32. Instruction — part 739
EXL-240
< SYMPTOM DIAGNOSIS >
EXTERIOR LIGHTING SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000004201542
CAUTION:
Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
Symptom
Possible cause
Inspection item
Headlamp does not
switch to the high beam.
One side
• Fuse
• Harness between IPDM E/R
and the front combination lamp
• Front combination lamp
(High beam relay)
• IPDM E/R
Headlamp (HI) circuit
Refer to
.
Both sides
Symptom diagnosis
"BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM"
Refer to
High beam indicator lamp is not turned ON.
(Headlamp switches to the high beam.)
• Combination meter
• BCM
• Combination meter.
Data monitor "HI-BEAM IND"
• BCM (HEAD LAMP)
Active test "HEADLAMP"
Headlamp does not
switch to the low beam.
One side
Front combination lamp (Low
beam relay)
—
Both sides
• Combination switch
• Harness between the combina-
tion switch and BCM
• BCM
Combination switch
Refer to
High beam request signal
• BCM
• IPDM E/R
IPDM E/R
Data monitor "HL HI REQ"
IPDM E/R
—
Headlamp does not turn
ON.
One side
• Fuse
• Bulb
• Harness between IPDM E/R
and the front combination lamp
• Front combination lamp
• IPDM E/R
Headlamp (LO) circuit
Hallogen, refer to
Both sides
Symptom diagnosis
"BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON"
Refer to
.
Headlamp does not turn
OFF.
When the ignition
switch is turned ON
• BCM
• Combination switch
Combination switch
Refer to
The ignition switch is
turned OFF (After acti-
vating the battery sav-
er).
IPDM E/R
—
Headlamp is not turned ON/OFF with the lighting
switch AUTO.
• Combination switch
• Harness between the combina-
tion switch and BCM
• BCM
Combination switch
Refer to
• Optical sensor
• Harness between the optical
sensor and BCM
• BCM
Optical sensor
Refer to
.
EXTERIOR LIGHTING SYSTEM SYMPTOMS
EXL-241
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Daytime light system does not activate.
• Either high beam bulb
• Parking brake switch
• Combination switch
• BCM
• IPDM E/R
• Daytime light relay
• Harness between IPDM E/R
and daytime light relay.
Daytime light system description.
Refer to
.
Front fog lamp is not
turned ON.
One side
• Front fog lamp bulb
• Harness between IPDM E/R
and the front combination lamp
• Front combination lamp
• IPDM E/R
Front fog lamp circuit
Refer to
.
Both side
Symptom diagnosis
"BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON"
Refer to
Parking lamp is not turned
ON.
One side
• Fuse
• Parking lamp bulb
• Harness between IPDM E/R
and the front/rear combination
lamp
• Front/rear combination lamp
• IPDM E/R
Parking lamp circuit
Refer to
.
Both sides
Symptom diagnosis
"PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED
ON"
Refer to
Turn signal lamp does not
blink.
Indicator lamp is nor-
mal.
(The applicable side
performs the high flash-
er activation).
• Harness between BCM and
each turn signal lamp
• Turn signal lamp bulb
• Door mirror (if equipped with
turn signals in the door mirrors)
Turn signal lamp circuit
Refer to
.
Turn signal indicator lamp
does not blink.
One side
Combination meter
—
Both sides
(Always)
• Turn signal indicator lamp sig-
nal
• Combination meter
• BCM
• Combination meter.
Data monitor "TURN IND"
• BCM (FLASHER)
Active test "FLASHER"
Both sides
(Does blink when acti-
vating the hazard warn-
ing lamp with the
ignition switch OFF)
• The combination meter power
supply and the ground circuit
• Combination meter
Combination meter
Power supply and the ground circuit
Refer to
.
Symptom
Possible cause
Inspection item
EXL-242
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000004201543
XENON HEADLAMP
• The brightness and color of the light may vary slightly immediately after turning the headlamp ON. This con-
dition will remain until the xenon bulb becomes stable. This is normal.
• Illumination time lag may occur between right and left. This is normal.
AUTO LIGHT SYSTEM
The auto light system may not turn the headlamp ON/OFF immediately after passing a dark area or a bright
area (short tunnel, sky bridge, shadowed area etc.). This is normal.
BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM
EXL-243
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM
Description
INFOID:0000000004201544
The headlamps (both sides) do not switch to high beam when the lighting switch is in the HI or PASS setting.
Diagnosis Procedure
INFOID:0000000004201545
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 2
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select "HL HI REQ" of IPDM E/R DATA MONITOR item.
2. With operating the lighting switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 3
NO
>> Replace BCM. Refer to
BCS-96, "Removal and Installation"
3.
HEADLAMP (HI) CIRCUIT INSPECTION
Check the headlamp (HI) circuit. Refer to
Is the headlamp (HI) circuit normal?
YES
>> Replace IPDM E/R. Refer to
PCS-48, "Removal and Installation"
.
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
HL HI REQ
Lighting switch
(2ND)
HI or PASS
ON
Except for HI or
PASS
OFF
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст