Nissan Altima L32. Instruction — part 624
EM-32
< ON-VEHICLE REPAIR >
[QR25DE]
OIL PAN AND OIL STRAINER
OIL PAN AND OIL STRAINER
Removal and Installation
INFOID:0000000004202118
REMOVAL
WARNING:
To avoid the danger of being scalded, never drain the engine oil when the engine is hot.
1. Drain engine oil. Refer to
2. Remove the front exhaust tube. Refer to
3. Remove power steering cooler hose bracket from suspension member.
4. Remove the front suspension member for clearance to remove the oil pan. Refer to
5. Remove the lower oil pan bolts in the order as shown, using
power tool.
AWBIA0012GB
1.
Oil level gauge guide
2.
Oil pan, upper
3.
Cylinder block
4.
Oil filter
5.
Oil strainer
6.
Drain plug
7.
Oil pan, lower
8.
Rear plate cover
9.
O-ring
A. To oil pan, lower
ALBIA0180ZZ
OIL PAN AND OIL STRAINER
EM-33
< ON-VEHICLE REPAIR >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
6. Remove the lower oil pan using Tool.
NOTE:
Tap gently to cut sealant around the pan; do not damage the
mating surface using Tool.
7. Remove the oil strainer.
8. Remove rear plate cover, and four engine-to transaxle bolts, using power tool.
9. Loosen the upper oil pan bolts in the order shown to remove
upper oil pan, using power tool.
10. Remove upper oil pan using Tool.
NOTE:
Tap gently to cut sealant around the pan; do not damage the
mating surface using Tool.
INSPECTION AFTER REMOVAL
• Clean the oil strainer screen to remove any foreign material.
INSTALLATION
Installation is in the reverse order of removal.
• Apply Genuine Silicone RTV Sealant or equivalent to the upper oil
pan at the specified sealant bead diameter (A) as shown. Refer to
GI-15, "Recommended Chemical Products and Sealants"
.
CAUTION:
Install two new O-rings in the upper oil pan.
Tool number
: KV10111100 (J-37228)
WBIA0475E
ALBIA0181ZZ
Tool number
: KV10111100 (J-37228)
WBIA0475E
Sealant bead diameter (A) : 4.0 - 5.0 mm
(0.157 - 0.197 in)
ALBIA0183ZZ
EM-34
< ON-VEHICLE REPAIR >
[QR25DE]
OIL PAN AND OIL STRAINER
• Tighten the upper oil pan bolts in the order as shown.
• Apply Genuine Silicone RTV Sealant or equivalent to the lower oil
pan at the specified sealant bead diameter (A) as shown. Refer to
GI-15, "Recommended Chemical Products and Sealants"
.
• Tighten the lower oil pan bolts in the numerical order shown.
CAUTION:
Wait at least 30 minutes after the oil pans are installed before
filling the engine with oil.
INSPECTION AFTER INSTALLATION
• Check for any engine oil leaks with the engine at operating temperature and running at idle.
ALBIA0184ZZ
Sealant bead diameter (A)
: 4.0 - 5.0 mm
(0.157 - 0.197 in)
ALBIA0182ZZ
ALBIA0185ZZ
IGNITION COIL
EM-35
< ON-VEHICLE REPAIR >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
IGNITION COIL
Removal and Installation
INFOID:0000000004202119
REMOVAL
1. Remove the engine cover.
2. Disconnect the harness connector from the ignition coil.
3. Remove the ignition coil.
CAUTION:
Do not drop or shock it.
INSTALLATION
Installation is in the reverse order of removal.
AWBIA0208GB
1.
Ignition coil
2.
Spark plug
3.
Rocker cover
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст