Nissan Altima L32. Instruction — part 90
AV-352
< COMPONENT DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
SUBWOOFER (SEDAN)
1. Connect AV control unit connector M47 and BOSE speaker
amp. connector B121.
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
4. Check the signal between AV control unit harness connector
M47 terminals with CONSULT-III or oscilloscope.
Are the audio signal voltage readings as specified?
YES
>> Replace BOSE speaker amp. Refer to
"Removal and Installation - Sedan"
.
NO
>> Replace AV control unit. Refer to
Connector
Terminals
Condition
Reference
signal
(+)
(-)
M47
5
6
Receive audio
signal
14
15
ALNIA0172ZZ
SKIA0177E
AV
AMP ON SIGNAL CIRCUIT
AV-353
< COMPONENT DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
AMP ON SIGNAL CIRCUIT
Description
INFOID:0000000004206654
When the audio system is turned on, a voltage signal is supplied from the AV control unit to the BOSE speaker
amp. When this signal is received, the BOSE speaker amp. will turn on.
Diagnosis Procedure
INFOID:0000000004206655
1.
CHECK AMP ON SIGNAL (BOSE SPEAKER AMP)
1. Turn audio system ON.
2. Check voltage between BOSE speaker amp. harness connector
B121 terminal 60 and ground.
Is voltage greater than 6.5V?
YES
>> INSPECTION END.
NO
>> GO TO 2
2.
CHECK AMP ON SIGNAL (AV CONTROL UNIT)
Check voltage between AV control unit harness connector M47 ter-
minal 16 and ground.
Is voltage approximately 6.5 volts?
YES
>> Repair harness or connector.
NO
>> Replace AV control unit. Refer to
60 - Ground
: More than approx. 6.5V
ALNIA0147ZZ
16 - Ground
: More than approx. 6.5V
ALLIA0254ZZ
AV-354
< COMPONENT DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
STEERING SWITCH
STEERING SWITCH
Description
INFOID:0000000004206656
When one of the steering wheel audio control switches is pushed, the resistance in the steering switch circuit
changes depending on which button is pushed.
Diagnosis Procedure
INFOID:0000000004206657
1.
CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect AV control unit connector M46 and spiral cable connector M30.
3. Check continuity between AV control unit connector M46 termi-
nals 25, 26, and 27 and spiral cable connector M30 terminals
24, 31, and 33.
4. Check continuity between AV control unit connector M46 (A) and
ground.
Are the continuity test results as specified?
YES
>> GO TO 2
NO
>> Repair harness.
2.
SPIRAL CABLE CHECK
1. Disconnect spiral cable connector M88.
2. Check continuity between spiral cable harness connector M30
and M88.
Are the continuity test results as specified?
YES
>> GO TO 3.
NO
>> Replace spiral cable. Refer to
SR-8, "Removal and Installation"
3.
CHECK STEERING SWITCH
Check steering switch. Refer to
AV-355, "Component Inspection"
.
Does the steering switch pass inspection?
YES
>> INSPECTION END.
NO
>> Replace steering switch. Refer to
AV-448, "Removal and Installation"
A
B
Continuity
Connector
Terminal
Connector
Terminal
M46
25
M30
24
Yes
26
33
27
31
A
–
Continuity
Connector
Terminal
M46
25
Ground
No
26
27
ALLIA0255ZZ
A
B
Continuity
Connector
Terminal
Connector
Terminal
M30
24
M88
14
Yes
31
15
33
17
ALNIA0931GB
AV
STEERING SWITCH
AV-355
< COMPONENT DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Component Inspection
INFOID:0000000004206658
Measure the resistance between the steering switch connector terminals 14 to 17 and 15 to 17.
Standard
Between terminals 14 and
17
ENTER switch ON
: 2003 – 2043
Ω
switch ON
: 716 – 730
Ω
MENU DOWN switch ON
: 318 – 324
Ω
MENU UP switch ON
: 120 – 122
Ω
SOURCE switch ON
: 0
Ω
Between terminals 15 and
17
switch ON
: 716 – 730
Ω
switch ON
: 318 – 324
Ω
VOL UP switch ON
: 120 – 122
Ω
VOL DOWN switch ON
: 0
Ω
JSNIA0112GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст