Nissan Altima L32. Instruction — part 115
AV-452
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITH NAVIGATION]
AUDIO ANTENNA (SEDAN)
AUDIO ANTENNA (SEDAN)
Location of Antenna
INFOID:0000000004206706
Window Antenna Repair
INFOID:0000000004206707
ELEMENT CHECK
1. Attach probe circuit tester (ohm setting) to antenna terminal on
each side.
AWNIA1817ZZ
1.
In-line connectors M87, M501
2.
AV control unit harness
3.
AV control unit
4.
Satellite antenna
5.
AV control unit antenna feeder
6.
Satellite radio antenna feeder
7.
Window Antenna
8.
Antenna amp.
9.
Satellite radio tuner
SEL250I
AV
AUDIO ANTENNA (SEDAN)
AV-453
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• When measuring continuity, wrap tin foil around the top of
probe. Then, press the foil against the wire with your finger.
2. If an element is broken, no continuity will exist.
3. To locate a break, move probe along element. Tester indication
will change abruptly when probe passes the broken point.
REPAIR EQUIPMENT
• Conductive silver composition (DuPont No. 4817 or equivalent)
• Ruler 30 cm (11.8 in) long
• Drawing pen
• Heat gun
• Alcohol
• Cloth
REPAIRING PROCEDURE
SEL122R
SEL252I
SEL253I
AV-454
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITH NAVIGATION]
AUDIO ANTENNA (SEDAN)
1. Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
2. Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.
3. Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
4. After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
5. Apply a constant stream of hot air directly to the repaired area
for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.
PIIA0215E
SEL012D
SEL013D
AV
ANTENNA AMP.
AV-455
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
ANTENNA AMP.
Removal and Installation - Coupe
INFOID:0000000004206708
REMOVAL
1. Remove the rear pillar finisher RH. Refer to
2. Detach the antenna amp harness clip (B), disconnect the
antenna amp connectors (A), remove the antenna amp screw
(C) and remove the antenna amp (1).
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation - Sedan
INFOID:0000000004206709
REMOVAL
1. Remove the rear pillar finisher RH. Refer to
2. Partially remove the side curtain air bag module RH to gain access to the antenna amp. Refer to
3. Detach the antenna amp harness clip (A), disconnect the
antenna amp connectors (B), remove the antenna amp screw
(C) and remove the antenna amp (1).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA0917ZZ
ALNIA0043ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст