Nissan Altima L32. Instruction — part 982
PARKING BRAKE SYSTEM
PB-3
< ON-VEHICLE MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
ON-VEHICLE MAINTENANCE
PARKING BRAKE SYSTEM
PEDAL TYPE
PEDAL TYPE : Inspection
INFOID:0000000004513195
• Check control device for wear or other damage. Replace if necessary.
• Check wires for wear or damage. Replace if necessary.
• Check warning lamp and switch. Replace if necessary.
• Check parts at each connecting position and if found deformed or damaged, replace as necessary.
• Check if the parking brake pedal stroke is within specification. Refer to
PB-3, "PEDAL TYPE : Adjustment"
.
PEDAL TYPE : Adjustment
INFOID:0000000004513196
ADJUSTMENT
1. Remove rear wheel and tires. Refer to
.
2. Insert a deep socket wrench onto adjusting nut. Rotate adjusting
nut to fully loosen cable, and then release parking brake pedal.
3. Secure disc rotor to hub using wheel nut so as not to tilt disc
rotor.
4. Remove adjuster hole plug installed on the disc rotor. Turn the
adjuster in direction (A) using a suitable tool or a flat-bladed
screwdriver as shown, until disc rotor is locked. Turn the
adjuster in the opposite direction by 5 or 6 notches after locking.
5. Rotate disc rotor to make sure that there is no drag. Install the
adjuster hole plug.
6. Adjust parking brake cable with the following procedure.
a. Operate parking brake pedal 10 or more times with a full stroke
of 194.3 mm (7.6 in).
b. Rotate adjusting nut to adjust parking brake pedal stroke using a
deep socket wrench.
c. Operate parking brake pedal with a force of 294 N (30 kg-f, 66 lb-f), make sure the pedal stroke is within
the specified number of notches. Check it by listening and counting the ratchet clicks.
d. Make sure that there is no drag on the parking brake with the parking brake pedal completely released.
LEVER TYPE
LEVER TYPE : Inspection
INFOID:0000000004206767
• Check control device for wear or other damage. Replace if necessary.
• Check wires for wear or damage. Replace if necessary.
• Check warning lamp and switch. Replace if necessary.
• Check parts at each connecting position and if found deformed or damaged, replace as necessary.
• Check if the control lever stroke is within specification. Refer to
PB-4, "LEVER TYPE : Adjustment"
SFIA2961E
Pedal stroke (number of notches)
PB-11, "Parking Brake Control"
.
PFIA0295E
PB-4
< ON-VEHICLE MAINTENANCE >
PARKING BRAKE SYSTEM
LEVER TYPE : Adjustment
INFOID:0000000004206768
1. Fully engage the control lever.
2. Loosen the parking brake cable adjusting nut and fully release
the control lever.
3. Adjust clearance of the rear parking brake shoes. Refer to
.
4. Depress the brake pedal fully more than five times.
5. Make sure that no drag exists while rotating the rear wheel and
tires.
6. Operate control lever 10 times or more with a full stroke of 99.5
mm (3.9 in).
7. Adjust control lever by turning adjusting nut.
8. Pull control lever with a force of 294 N (30 kg-f, 66 lb-f). Check
control lever stroke and ensure smooth operation.
9. After adjustment, check that there is no drag while the control lever is being released. If drag exists, per-
form the following:
• Remove the rear disc rotor. Refer to
PER ASSEMBLY : Removal and Installation"
. Verify the toggle
lever returns to stopper when the parking brake lever is
released.
• If toggle lever does not return to stopper, loosen adjusting nut.
• Install rear disc rotor and adjust shoe clearance. Refer to
PB-9, "Removal and Installation"
Lever stroke (number of notches) : Refer to
PB-11, "Parking Brake Control"
LFIA0094E
LFIA0095E
LFIA0094E
PARKING BRAKE SHOE
PB-5
< ON-VEHICLE MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PARKING BRAKE SHOE
Inspection
INFOID:0000000004206769
LINING THICKNESS INSPECTION
• Check thickness of lining.
DRUM INNER DIAMETER INSPECTION
• Check inner diameter of drum in rear disc rotor.
OTHER INSPECTIONS
• Check the following:
- Lining for excessive wear, damage, and peeling.
- Shoe sliding surface for excessive wear and damage.
- Anti-rattle pin for excessive wear and corrosion.
- Return spring for sagging.
• Make sure that adjuster moves smoothly.
• Visually check the inside of drum for excessive wear, cracks, and damage. Check the inside of drum using a
pair of vernier calipers.
• Replace with new parts as necessary.
Standard thickness (new) (A)
: Refer to
Wear limit thickness (A)
: Refer to
SBR021A
Standard inner diameter (new) : Refer to
Wear limit of inner diameter
: Refer to
SBR768A
PB-6
< ON-VEHICLE REPAIR >
PARKING BRAKE CONTROL
ON-VEHICLE REPAIR
PARKING BRAKE CONTROL
PEDAL TYPE
PEDAL TYPE : Exploded View
INFOID:0000000004513199
PEDAL TYPE : Removal and Installation
INFOID:0000000004513201
REMOVAL
1. Remove rear wheel and tires. Refer to
.
1.
Control device assembly
2.
Parking brake switch
3.
Pedal pad
4.
Adjusting nut
5.
Lock plate
6.
Front cable
7.
Rear cable RH
8.
Rear cable LH
9.
Equalizer
10. Spring
11. Pin
Front
AWFIA0511GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст