Nissan Altima L32. Instruction — part 659
EM-172
< ON-VEHICLE REPAIR >
[VQ35DE]
REAR TIMING CHAIN CASE
REAR TIMING CHAIN CASE
Component
INFOID:0000000004202171
• Refer to
EM-111, "Precaution for Liquid Gasket"
• Before installation, wipe off any protruding sealant.
CAUTION:
• After removing timing chain, do not turn the crankshaft and camshaft separately, or the valves will
strike the pistons.
• When installing camshafts, chain tensioners, oil seals, or other sliding parts, lubricate contacting
surfaces with new engine oil.
• Apply new engine oil to bolt threads and seat surfaces when installing camshaft sprockets, camshaft
brackets, and crankshaft pulley.
• Before disconnecting fuel hose, release fuel pressure. Refer to
.
• Before removing the upper oil pan, remove the crankshaft position sensor (POS).
• Be careful not to damage sensor edges.
• Do not spill engine oil or coolant on drive belts.
1.
Timing chain tensioner
2.
Internal chain guide
3.
Timing chain tensioner
4.
Camshaft sprocket (EXH)
5.
Timing chain (secondary)
6.
Timing chain (primary)
7.
Camshaft sprocket (INT)
8.
Camshaft sprocket (INT)
9.
Timing chain (secondary)
10. Camshaft sprocket (EXH)
11. Slack guide
12. Crankshaft sprocket
13. Rear timing chain case
14. Tension guide
15. O-ring
AWBIA0578GB
REAR TIMING CHAIN CASE
EM-173
< ON-VEHICLE REPAIR >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Removal and Installation
INFOID:0000000004202172
REMOVAL
1. Remove the engine assembly. Refer to
EM-202, "Removal and Installation"
.
2. Remove the primary and secondary timing chains. Refer to
.
3. Remove the rear timing chain case.
CAUTION:
• Do not remove the plate metal cover for the oil passage.
• After removing the chain case, do not apply any load to
the case that might bend it.
a. Loosen and remove the rear timing chain case bolts in the order as shown.
b. Cut the sealant with an appropriate tool and remove the rear timing chain case.
4. Remove O-rings to timing chain case and cylinder block.
5. Use a scraper to remove all of the old Silicone RTV Sealant from
the front and rear timing chain case and opposite mating sur-
faces.
CAUTION:
Do not damage the mating surfaces.
KBIA1307E
AWBIA0709ZZ
SEM428G
EM-174
< ON-VEHICLE REPAIR >
[VQ35DE]
REAR TIMING CHAIN CASE
6. Remove all old Silicone RTV Sealant from all the bolt holes and
bolts.
CAUTION:
Do not damage the threads or mating surfaces.
INSTALLATION
1. Install O-rings on cylinder block.
2. Apply Genuine Silicone RTV Sealant or equivalent, to the rear timing chain case using Tool as shown.
GI-15, "Recommended Chemical Products and Sealants"
.
CAUTION:
• For (a), completely wipe out liquid gasket extended on a portion touching at engine coolant.
• Apply liquid gasket on installation position of water pump and cylinder completely.
SEM161F
PBIC0788E
Tool number
: WS39930000 ( — )
REAR TIMING CHAIN CASE
EM-175
< ON-VEHICLE REPAIR >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
3. Align the rear timing chain case and water pump assembly with the dowel pins (RH and LH) on the cylin-
der block and install the case. Make sure the O-rings stay in place during installation.
a. Tighten the bolts in the numerical order as shown. There are two bolt lengths used. Follow the chart below
for proper bolt length specifications.
PBIC2680E
AWBIA0710ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст