Nissan Altima L32. Instruction — part 1102
PRECAUTIONS
PWC-175
< PRECAUTION >
[LH ONLY ANTI-PINCH-SEDAN]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000004205062
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000004499256
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT-III.
PWC-176
< SYMPTOM DIAGNOSIS >
[LH ONLY ANTI-PINCH-SEDAN]
NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY SWITCH
SYMPTOM DIAGNOSIS
NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY
SWITCH
Diagnosis Procedure
INFOID:0000000004205053
1.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Check BCM power supply and ground circuit.
.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH POWER SUPPLY AND
GROUND CIRCUIT
Check main power window and door lock/unlock switch power supply and ground circuit.
PWC-103, "POWER WINDOW MAIN SWITCH : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH
Check main power window and door lock/unlock switch.
PWC-103, "POWER WINDOW MAIN SWITCH : Component Function Check"
Is the inspection result normal?
YES
>> Inspection end.
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
DRIVER SIDE POWER WINDOW ALONE DOES NOT OPERATE
PWC-177
< SYMPTOM DIAGNOSIS >
[LH ONLY ANTI-PINCH-SEDAN]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
DRIVER SIDE POWER WINDOW ALONE DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000004205054
1.
CHECK FRONT POWER WINDOW MOTOR LH
Check front power window motor LH.
PWC-114, "DRIVER SIDE : Component Function Check"
.
Is the inspection result normal?
YES
>> Inspection end.
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
PWC-178
< SYMPTOM DIAGNOSIS >
[LH ONLY ANTI-PINCH-SEDAN]
FRONT PASSENGER SIDE POWER WINDOW ALONE DOES NOT OPERATE
FRONT PASSENGER SIDE POWER WINDOW ALONE DOES NOT OPER-
ATE
Diagnosis Procedure
INFOID:0000000004205055
1.
CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH
Check power window and door lock/unlock switch RH.
PWC-108, "FRONT POWER WINDOW SWITCH : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK FRONT POWER WINDOW MOTOR RH CIRCUIT
Check front power window motor RH circuit.
PWC-116, "PASSENGER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> Inspection end.
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст