Nissan Altima L32. Instruction — part 186
CHG-28
< ON-VEHICLE REPAIR >
GENERATOR
operation inspection should be performed after replacing the generator, and then make sure that the system
operates normally. Refer to
VQ35DE
REMOVAL
1. Disconnect the battery negative terminal. Refer to
PG-68, "Removal and Installation"
(Coupe models) or
PG-139, "Removal and Installation"
2. Partially drain engine coolant. Refer to
CO-35, "Changing Engine Coolant"
3. Remove engine room cover.
4. Remove RH front wheel and tire assembly. Refer to
5. Remove engine side undercover using power tools.
6. Remove air cleaner and duct assembly. Refer to
EM-129, "Removal and Installation"
7. Remove battery tray. Refer to
PG-68, "Removal and Installation"
(Sedan models).
8. Remove cooling fan assembly. Refer to
CO-40, "Removal and Installation"
9. Evacuate A/C system. Refer to
HA-32, "HFC-134a (R-134a) Service Procedure"
10. Remove drive belt. Refer to
EM-121, "Removal and Installation"
11. Remove the A/C compressor. Refer to
HA-36, "Removal and Installation for Compressor - VQ35DE Mod-
12. Remove idler pulley.
13. Remove A/C idler pulley.
14. Disconnect oil pressure switch.
15. Disconnect the generator harness connectors.
16. Remove the generator bolt and nuts, using power tools.
17. Slide the generator out and remove.
ALMIA0453GB
1.-3. Tightening order
4.
Generator
5.
B terminal nut
6.
Generator bracket
Front
CHG
GENERATOR
CHG-29
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Be sure to tighten “B” terminal nut carefully.
• Install generator and check tension of belt. Refer to
EM-121, "Checking Drive Belts"
• For this model, the power generation voltage variable control system that controls the power generation volt-
age of the generator has been adopted. Therefore, the power generation voltage variable control system
operation inspection should be performed after replacing the generator, and then make sure that the system
operates normally. Refer to
.
Inspection
INFOID:0000000004205669
GENERATOR PULLEY INSPECTION
Perform the following.
• Make sure that generator pulley does not rattle.
• Make sure that generator pulley nut is tight.
Generator pulley nut : 118 N·m (12.0 kg-m, 87 ft-lb)
CHG-30
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Generator
INFOID:0000000004205670
Application
QR25DE
VQ35DE
Type
TG12C033
H130-135D1
Valeo
Mitsubishi
Nominal rating
14V-110A
12V-130A
Ground polarity
Negative
Minimum revolution under no-load
1,200 rpm
1,000 rpm
Hot output current (When 13.5 volts is applied)
More than 47A/1,500 rpm
More than 74A/1,800 rpm
More than 103A/2,500 rpm
More than 117A/5,000 rpm
More than 61A/1,500 rpm
More than 109A/2,500 rpm
More than 129A/5,000 rpm
Regulated output voltage
13.5V @ 5,000 rpm @ 20
°C
13.5V @ 5,000 rpm @ 20
°C
Adjustment range of power generation variable
voltage control
11.4 - 15.6V
11.4 - 15.6V
CL-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
CL
A
B
CL
N
O
P
CONTENTS
CLUTCH
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions Necessary for Steering Wheel Rota-
tion after Battery Disconnect . . . . . . . . .....
Precaution for Procedure without Cowl Top Cover
. ..
Service Notice or Precautions . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
Commercial Service Tools . . . . . . . . . ....
ON-VEHICLE MAINTENANCE . . . . . .
CLUTCH PEDAL . . . . . . . . . . . . .
Inspection and Adjustment . . . . . . . . . ....
CLUTCH FLUID . . . . . . . . . . . . ...
Air Bleeding Procedure . . . . . . . . . . .....
ON-VEHICLE REPAIR . . . . . . . . ..
CLUTCH PEDAL . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . .
CLUTCH MASTER CYLINDER . . . . . .
Removal and Installation . . . . . . . . . . .
CLUTCH PIPING . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
CSC (CONCENTRIC SLAVE CYLINDER) . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
CLUTCH DISC AND CLUTCH COVER . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Clutch Control System . . . . . . . . . . . .
Clutch Pedal . . . . . . . . . . . . . . .
Clutch Disc . . . . . . . . . . . . . . . ..
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст