Nissan Altima L32. Instruction — part 80
AV-312
< COMPONENT DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
U1244 GPS ANTENNA
U1244 GPS ANTENNA
Description
INFOID:0000000004206620
DTC Logic
INFOID:0000000004206621
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000004206622
1.
GPS ANTENNA CHECK
Inspect GPS antenna and antenna feeder for damage or poor connection.
Is the GPS antenna and feeder clean and undamaged?
YES
>> GO TO 2
NO
>> Repair or replace malfunctioning parts.
2.
CHECK AV CONTROL UNIT VOLTAGE
1. Turn ignition switch ON.
2. Check voltage between AV control unit connector M90 terminal
73 and ground.
Is the voltage reading as specified?
YES
>> Replace GPS antenna. Refer to
NO
>> Replace AV control unit. Refer to
DTC
CONSULT-III display
Detection condition
U1244
GPS ANTENNA CONN
[U1244]
GPS antenna connection malfunction is detected.
73 - Ground
: Approx. 5V
ALLIA0240ZZ
AV
U124C CD CHANGER
AV-313
< COMPONENT DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U124C CD CHANGER
Description
INFOID:0000000004206623
DTC Logic
INFOID:0000000004206624
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000004206625
1.
CHECK CD CHANGER POWER SUPPLY AND GROUND CIRCUIT
Check CD changer power supply and ground circuit. Refer to
AV-318, "CD CHANGER : Diagnosis Proce-
.
Do power and ground check OK?
YES
>> GO TO 2
NO
>> Repair power supply or ground circuit.
2.
CHECK COMMUNICATION CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect CD changer connector M42 and AV control unit connector M48.
3. Check continuity between CD changer harness connector M42
(A) terminals 8, 9 and 10 and AV control unit harness connector
M48 (B) terminals 69, 70 and 72.
4. Check continuity between CD changer harness connector M42
(A) terminals 8, 9, 10 and ground.
Are the continuity test results as specified?
YES
>> GO TO 3
NO
>> Repair harness or connector.
3.
CHECK REQUEST SIGNAL
1. Connect CD changer connector and AV control unit connector.
2. Turn ignition switch ON.
3. Check signal between CD changer harness connector M42 ter-
minal 8 and ground.
DTC
CONSULT-III display
Detection condition
U124C
N-BUS CD CHG CONN
[U124C]
• A malfunction is detected in CD changer power supply and ground circuits
• Malfunction occurs in request signal circuit. (Between CD changer and AV control unit)
• Malfunction occurs in communication signal circuit. (Between CD changer and AV control
unit)
8 - 72
: Continuity should exist.
9 - 69
: Continuity should exist.
10 - 70
: Continuity should exist.
8, 9, 10 - Ground
: Continuity should not exist.
ALLIA0236ZZ
8 - Ground
ALLIA0237ZZ
SKIA9299J
AV-314
< COMPONENT DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
U124C CD CHANGER
Are the voltage readings as specified?
YES
>> GO TO 4
NO
>> Replace CD changer. Refer to
AV-439, "Removal and Installation"
.
4.
CHECK COMMUNICATION SIGNAL
Check signal between CD changer harness connector M42 terminal
9 and ground.
Are the voltage readings as specified?
YES
>> GO TO 5
NO
>> Replace CD changer. Refer to
AV-439, "Removal and Installation"
.
5.
CHECK COMMUNICATION SIGNAL
Check signal between CD changer harness connector M42 terminal
10 and ground.
Are the voltage readings as specified?
YES
>> Inspection End.
NO
>> Replace AV control unit. Refer to
AV-437, "Removal and Installation"
.
9 - Ground
ALLIA0238ZZ
SKIA9300J
10 - Ground
ALLIA0239ZZ
SKIA9300J
AV
POWER SUPPLY AND GROUND CIRCUIT (COUPE)
AV-315
< COMPONENT DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
POWER SUPPLY AND GROUND CIRCUIT (COUPE)
AV CONTROL UNIT
AV CONTROL UNIT : Diagnosis Procedure
INFOID:0000000004206626
1.
CHECK FUSE
Check that the following fuses of the AV control unit are not blown.
Are the fuses OK?
YES
>> GO TO 2
NO
>> Be sure to eliminate cause of malfunction before installing new fuse.
2.
CHECK POWER SUPPLY CIRCUIT
Check voltage between AV control unit harness connector and
ground.
Are the voltage tests as specified?
YES
>> GO TO 3
NO
>> Check harness between AV control unit and fuse.
3.
CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect AV control unit connectors.
3. Check continuity between AV control unit harness connector
M47 terminal 19 and ground.
Does continuity exist?
YES
>> Inspection End.
NO
>> Repair harness or connector.
REAR VIEW CAMERA CONTROL UNIT
REAR VIEW CAMERA CONTROL UNIT : Diagnosis Procedure
INFOID:0000000004206627
1.
CHECK FUSE
Check that the following fuses of the rear view camera control unit are not blown.
Unit
Terminals
Signal name
Fuse No.
AV control unit
20
Battery power
24
7
Ignition switch ACC or ON
19
10
Ignition switch ON or START
3
(+)
(-)
Ignition switch po-
sition
Value (Ap-
prox.)
Connector
Terminal
M47
20
Ground
OFF
Battery volt-
age
7
ACC
10
ON
ALLIA0241ZZ
Signal name
Continuity
Ground
Continuity should exist.
ALLIA0242ZZ
Unit
Terminals
Signal name
Fuse No.
Rear view camera control unit
1
Battery power
24
2
Ignition switch ACC or ON
19
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст