Nissan Pathfinder (2012 year). Instruction — part 361
EXL-4
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000007355103
OVERALL SEQUENCE
AWLIA1837GB
August 2012
2012 Pathfinder
DIAGNOSIS AND REPAIR WORKFLOW
EXL-5
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DETAILED FLOW
1.
INTERVIEW FOR MALFUNCTION
Find out what the customer's concerns are.
>> GO TO 2
2.
SYMPTOM CHECK
Verify the symptom from the customer's information.
>> GO TO 3
3.
BASIC INSPECTION
Check the operation of each part. Check that any concerns occur other than those mentioned in the customer
interview.
>> GO TO 4
4.
SELF-DIAGNOSIS WITH CONSULT
Perform the self diagnosis with CONSULT. Check that any DTC is detected.
Is any DTC detected?
YES
>> GO TO 5
NO
>> GO TO 6
5.
TROUBLE DIAGNOSIS BY DTC
Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.
>> GO TO 9
6.
FAIL-SAFE ACTIVATION CHECK
Determine if the customer's concern is related to fail-safe activation.
Does the fail-safe activate?
YES
>> GO TO 7
NO
>> GO TO 8
7.
SYSTEM DIAGNOSIS
Perform the system diagnosis for the system in which the fail-safe activates. Specify the malfunctioning part.
>> GO TO 9
8.
SYMPTOM DIAGNOSIS
Perform the symptom diagnosis. Specify the malfunctioning part.
>> GO TO 9
9.
MALFUNCTION PART REPAIR
Repair or replace the malfunctioning part.
>> GO TO 10
10.
REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT)
Perform the self diagnosis with CONSULT. Verify that no DTCs are detected. Erase all DTCs detected prior to
the repair. Verify that DTC is not detected again.
Is any DTC detected?
August 2012
2012 Pathfinder
EXL-6
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
YES
>> GO TO 5
NO
>> GO TO 11
11.
REPAIR CHECK (OPERATION CHECK)
Check the operation of each part.
Does it operate normally?
YES
>> Inspection End.
NO
>> GO TO 3
August 2012
2012 Pathfinder
HEADLAMP
EXL-7
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
SYSTEM DESCRIPTION
HEADLAMP
System Diagram
INFOID:0000000007355104
System Description
INFOID:0000000007355105
Control of the headlamp system operation is dependent upon the position of the combination switch (lighting
and turn signal switch). When the lighting switch is placed in the 2nd position, the BCM (body control module)
receives input requesting the headlamps and park lamps to illuminate. This input is communicated to the
IPDM E/R (intelligent power distribution module engine room) via the CAN communication lines. The CPU
(central processing unit) of the IPDM E/R controls the headlamp high and headlamp low relay coils. When
energized, these relays direct power to the respective headlamps, which then illuminate.
HIGH BEAM OPERATION/FLASH-TO-PASS OPERATION
With the lighting switch in the 2ND position and placed in HIGH position, the BCM receives input requesting
the headlamp high beams to illuminate. The flash to pass feature can be used any time and also sends a sig-
nal to the BCM. This input is communicated to the IPDM E/R via the CAN communication lines. The CPU of
the combination meter controls the ON/OFF status off the HIGH BEAM indicator. The CPU of the IPDM E/R
controls the headlamp high relay coil which supplies power to the high beam headlamps.
The combination meter receives a high beam request signal (ON) via the CAN communication lines and turns
the high beam indicator lamp ON.
Component Parts Location
INFOID:0000000007355106
AWLIA1909GB
WKIA4957E
August 2012
2012 Pathfinder
EXL-8
< SYSTEM DESCRIPTION >
HEADLAMP
Component Description
INFOID:0000000007355107
1.
IPDM E/R E122, E123, E124
2.
BCM M18, M20 (view with lower instru-
ment panel LH removed)
3.
Combination switch (lighting and turn
signal switch) M28
4.
Combination meter M24
Part name
Description
BCM
• Receives lighting switch requests via BCM combination switch
reading function.
• Sends headlamp high/low request signal to the IPDM E/R.
IPDM E/R
Activates the headlamp high and headlamp low relays upon re-
quest from the BCM.
Combination switch (lighting and turn signal switch)
Outputs lighting requests to the BCM.
August 2012
2012 Pathfinder
DAYTIME RUNNING LIGHT SYSTEM
EXL-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DAYTIME RUNNING LIGHT SYSTEM
System Diagram
INFOID:0000000007355108
System Description
INFOID:0000000007355109
The headlamp system for Canada vehicles is equipped with a daytime light control that activates the high
beam headlamps at approximately half illumination whenever the engine is operating. If the parking brake is
depressed before the engine is started the daytime lights will not be illuminated. The daytime lights will illumi-
nate once the parking brake is released. Thereafter, the daytime lights will continue to operate when the park-
ing brake is depressed.
OPERATION
The BCM monitors inputs from the parking brake switch and the combination switch (lighting and turn signal
switch) to determine when to activate the daytime light system. The BCM sends a daytime light request to the
IPDM E/R via the CAN communication lines. The IPDM E/R grounds the daytime light relay 1 which in turn,
provides power to the ground side of the LH high beam lamp. Power flows backward through the LH high
beam lamp to the IPDM E/R, through the high beam fuses, through the RH high beam lamp circuit to the RH
high beam lamp and on to ground. The high beam lamps are wired in series which causes them to illuminate
at a reduced intensity.
AWLIA1751GB
August 2012
2012 Pathfinder
EXL-10
< SYSTEM DESCRIPTION >
DAYTIME RUNNING LIGHT SYSTEM
Component Parts Location
INFOID:0000000007355110
Component Description
INFOID:0000000007355111
1.
IPDM E/R E119, E122, E123, E124
2.
Parking brake switch E53
3.
BCM M18, M20 (view with lower instru-
ment panel LH removed)
4.
ECM E16 (view with ECM cover re-
moved)
5.
Generator E205, E209
6.
Daytime light relay 1, E103
7.
Daytime light relay 2, E104
8.
Combination switch (lighting and turn
signal switch) M28
9.
Combination meter M24
WKIA4958E
Part name
Description
BCM
• Receives combination switch (lighting and turn signal switch)
inputs via BCM combination switch reading function.
• Receives parking brake depressed input from the parking
brake switch.
• Receives engine running status from the ECM via CAN com-
munication.
IPDM E/R
Receives daytime light request from the BCM and activates the
daytime light relay.
Combination switch (lighting and turn signal switch)
Outputs lighting requests to the BCM.
August 2012
2012 Pathfinder
DAYTIME RUNNING LIGHT SYSTEM
EXL-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Park brake switch
Outputs parking brake status to the combination meter which for-
wards that information to the BCM via CAN communication.
ECM
Outputs engine running status to the BCM.
August 2012
2012 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст