Nissan Pathfinder (2012 year). Instruction — part 443
INTERIOR ROOM LAMP
INL-65
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
1. Using a suitable tool (A), release the pawls and remove the
cargo lamp lens (1).
: Pawl
CAUTION:
Wrap a cloth around suitable tool to protect the housing
and lens.
2. Remove cargo lamp screws (2).
3. Disconnect the connector, then remove cargo lamp.
Installation
Installation is in the reverse order of removal.
Bulb Replacement
1. Using a suitable tool, release the pawls and remove the cargo lamp lens.
2. Release the cargo lamp bulb retainers (1), then pull bulb (2)
straight out to remove.
AWLIA1670ZZ
Cargo lamp bulb
: 12V - 8W
ALLIA0326ZZ
August 2012
2012 Pathfinder
INL-66
< REMOVAL AND INSTALLATION >
ILLUMINATION
ILLUMINATION
Removal and Installation
INFOID:0000000007355256
ILLUMINATION CONTROL SWITCH
Removal
The illumination control switch (1) is replaced as a part of the combi-
nation meter assembly. Refer to
MWI-89, "Removal and Installation"
.
Installation
Installation is in the reverse order of removal.
GLOVE BOX LAMP
Removal
1. Remove instrument lower panel RH and glove box. Refer to
IP-20, "Removal and Installation"
2. Rotate glove box lamp socket (3) with bulb (1) counterclockwise,
then pull away from lamp shield (2) on steering member to
remove.
: Vehicle front
Installation
Installation is in the reverse order of removal.
Bulb Replacement
1. Remove glove box lamp.
2. Pull bulb (2) straight out from glove box lamp socket (1) to
remove.
AT FINISHER LAMP
Removal
1. Remove AT finisher from center console. Refer to
IP-21, "Removal and Installation"
LKIA0579E
AWLIA1668ZZ
Glove box lamp bulb
: 12V - 3.4W
ALLIA0321ZZ
August 2012
2012 Pathfinder
ILLUMINATION
INL-67
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
2. Rotate AT finisher lamp socket (2) with bulb (3) counterclock-
wise, then pull away from finisher (1).
Installation
Installation is in the reverse order of removal.
Bulb Replacement
1. Remove AT finisher from center console. Refer to
IP-21, "Removal and Installation"
2. Remove AT finisher lamp socket (1), then pull bulb (2) straight
out from socket.
ALLIA0590ZZ
AT finisher lamp bulb
: 12V - 3W
ALLIA0321ZZ
August 2012
2012 Pathfinder
INL-68
< SERVICE DATA AND SPECIFICATIONS (SDS)
BULB SPECIFICATIONS
SERVICE DATA AND SPECIFICATIONS (SDS)
BULB SPECIFICATIONS
Interior Lamp/Illumination
INFOID:0000000007355257
*: Always check with the Parts Department for the latest parts information.
Item
Wattage (W)*
Front room/map lamp
8
Vanity lamp (if equipped)
*
Personal lamp (if equipped)
8
Room lamp (if equipped)
8
Cargo lamp
8
Glove box lamp
3.4
A/T finisher lamp
3
August 2012
2012 Pathfinder
IP-1
BODY INTERIOR
C
D
E
F
G
H
I
K
L
M
SECTION
IP
A
B
IP
N
O
P
CONTENTS
INSTRUMENT PANEL
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect . . . . . . . . .....
Precaution for Work . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ...
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . .
Work Flow . . . . . . . . . . . . . . . .....
Generic Squeak and Rattle Troubleshooting . . ....
Diagnostic Worksheet . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . ...
INSTRUMENT PANEL ASSEMBLY . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
STEERING COLUMN COVERS . . . . . . .
Removal and Installation . . . . . . . . . . .
CLUSTER LID A . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
INSTRUMENT LOWER PANEL LH . . . . ..
Removal and Installation . . . . . . . . . . .
CLUSTER LID C . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
CLUSTER LID D . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
UPPER GLOVE BOX . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
INSTRUMENT LOWER PANEL RH AND
GLOVE BOX . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
A/T FINISHER . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
CENTER CONSOLE . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY .
CENTER CONSOLE ASSEMBLY . . . . .
Disassembly and Assembly . . . . . . . . . .
INSTRUMENT LOWER PANEL RH AND
GLOVE BOX . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . . .
August 2012
2012 Pathfinder
IP-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007356037
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000007356038
NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″
LOCK
″
position.
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing work. If
DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the
″
ACC
″
position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
August 2012
2012 Pathfinder
PRECAUTIONS
IP-3
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
5. When the repair work is completed, return the ignition switch to the
″
LOCK
″
position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT.
Precaution for Work
INFOID:0000000007356039
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components.
- Water soluble dirt: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the dirty
area.
Then rub with a soft and dry cloth.
- Oily dirt: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the dirty area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with
a soft and dry cloth.
• Do not use organic solvent such as thinner, benzene, alcohol, or gasoline.
• For genuine leather seats, use a genuine leather seat cleaner.
August 2012
2012 Pathfinder
IP-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000007356040
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000007356041
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-39570)
Chassis ear
Locating the noise
—
(J-43980)
NISSAN Squeak and Rattle kit
Repairing the cause of noise
—
(J-46534)
Trim tool set
Removing trim components
SBT839
SBT840
AWJIA0483ZZ
(Kent-Moore No.)
Tool name
Description
Engine ear
Locating the noise
Power Tool
Loosening nuts, screws and bolts
SIIA0995E
PIIB1407E
August 2012
2012 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст