Nissan Terrano model r20 series 2004. Instruction — part 217
Vehicle Speed Sensor
⋅
A/T (Revolution sensor)
DESCRIPTION
The revolution sensor detects the revolution of the out put shaft
parking pawl lock gear and emits a pulse signal. The pulse signal
is sent to the TCM which converts it into vehicle speed.
ON BOARD DIAGNOSIS LOGIC
Diagnostic trouble code
Malfunction is detected when ...
Check items
(Possible cause)
:
VHCL SPEED SEN
⋅
A/T
TCM does not receive the proper volt-
age signal from the sensor.
I
Harness or connectors
(The sensor circuit is open or
shorted.)
I
Revolution sensor
:
1st judgement flicker
SELF-DIAGNOSIS CODE CONFIRMATION PROCEDURE
After the repair, perform the following procedure to confirm the
malfunction is eliminated.
1)
Start engine.
2)
Select “SELF-DIAG RESULTS” mode with CONSULT-II.
3)
Drive vehicle under the following conditions:
Selector lever in “D” position, vehicle speed higher than
30 km/h (19 MPH), throttle opening greater than 1/8 of
the full throttle position and driving for more than 5 sec-
onds.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ OR ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
1)
Start engine.
2)
Drive vehicle under the following conditions:
Selector lever in “D” position, vehicle speed higher than
30 km/h (19 MPH), throttle opening greater than 1/8 of
the full throttle position and driving for more than 5 sec-
onds.
3)
Perform self-diagnosis.
Refer to SELF-DIAGNOSTIC PROCEDURE (Without
CONSULT-II), AT-15.
YAT336
SAT252K
SAT806H
TROUBLE DIAGNOSIS FOR VHCL SPEED SEN
⋅
A/T
AT-52
DIAGNOSTIC PROCEDURE
CHECK REVOLUTION SENSOR.
Refer to “COMPONENT INSPECTION”
below.
OK
E
NG
Repair or replace revolu-
tion sensor.
CHECK INPUT SIGNAL.
1. Start engine.
2. Select “ECU INPUT SIGNALS” in
Data Monitor.
3. Read out the value of “VHCL/S
SE
⋅
A/T” while driving.
Check the value changes accord-
ing to driving speed.
----------------------------------------------------------------------------------------------------------------------- OR -----------------------------------------------------------------------------------------------------------------------
1. Start engine.
2. Check voltage between TCM ter-
minal
q
42
and ground while driving.
(Measure in AC range.)
Voltage:
At 0 km/h (0 MPH):
0V
At 30 km/h (19 MPH):
1V or more
(Voltage rises gradually in
response to vehicle speed.)
OK
E
NG
Check the following items:
I
Harness for short or
open between TCM and
revolution sensor (Main
harness)
I
Harness for short or
open between revolution
sensor and ECM (Main
harness)
I
Ground circuit for ECM
Refer to EC section
(“TROUBLE DIAGNOSIS
FOR POWER SUPPLY”).
Perform “SELF-DIAGNOSIS CODE CON-
FIRMATION PROCEDURE”.
OK
E
NG
1. Perform TCM input/
output signal inspection.
2. If NG, recheck TCM pin
terminals for damage or
loose connection with
harness connector.
INSPECTION END
COMPONENT INSPECTION
Revolution sensor
I
For removal, refer to AT-119.
I
Check resistance between terminals
q
1
,
q
2
and
q
3
.
Terminal No.
Resistance
q
1
q
2
500 - 650
Ω
q
2
q
3
No continuity
q
1
q
3
No continuity
YAT297
NAT218
H
H
H
TROUBLE DIAGNOSIS FOR VHCL SPEED SEN
⋅
A/T
Vehicle Speed Sensor
⋅
A/T (Revolution sensor)
(Cont’d)
AT-53
Wiring Diagram — AT — VSSMTR
LHD MODELS
YAT263
TROUBLE DIAGNOSIS FOR VHCL SPEED SEN
⋅
MTR
AT-54
RHD MODELS
YAT264
TROUBLE DIAGNOSIS FOR VHCL SPEED SEN
⋅
MTR
Wiring Diagram — AT — VSSMTR (Cont’d)
AT-55
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст