Nissan Terrano model r20 series 2004. Instruction — part 262
2. Select counter gear rear bearing shim.
Counter gear end play:
0 - 0.2 mm (0 - 0.008 in)
a. Measure distance “A” between upper surface of counter gear
rear bearing and mating surface of front case.
b. Select suitable shim using chart below.
Distance “A”
mm (in)
Suitable shim
Thickness
mm (in)
Part number
32.65 - 32.55
(1.2854 - 1.2815)
Not necessary
32.55 - 32.45
(1.2815 - 1.2776)
0.1 (0.004)
33112-C6900
32.45 - 32.35
(1.2776 - 1.2736)
0.2 (0.008)
33112-C6901
32.35 - 32.25
(1.2736 - 1.2697)
0.3 (0.012)
33112-C6902
32.25 - 32.15
(1.2697 - 1.2657)
0.4 (0.016)
33112-C6903
32.15 - 32.05
(1.2657 - 1.2618)
0.5 (0.020)
33112-33G00
32.05 - 31.95
(1.2618 - 1.2579)
0.6 (0.024)
33112-33G01
3. Place suitable shim on counter gear rear bearing with grease.
4. Apply gear oil to each part in front case.
5. Assemble center case assembly.
a. Install mainshaft on center case by tapping lightly.
Apply gear oil to mainshaft front bearing.
SMT335A
SMT334A
SMT336A
SMT406A
ASSEMBLY
TF-28
b. Install bearing retainer.
c. Put drive chain onto the front drive sprocket and front drive
shaft, and then put them in center case.
d. Install front drive shaft by tapping lightly.
e. Apply gear oil to needle bearings and install them into front
drive sprocket.
These needle bearings will be installed more easily if front
drive sprocket is rotated while installing them.
SMT407A
SMT408A
SMT409A
SMT410A
SMT411A
ASSEMBLY
TF-29
f.
Install 2-4 coupling sleeve with 2-4 shift fork.
Pay special attention to direction of coupling sleeve.
g. Install shifting inserts and spread spring.
Pay special attention to direction of shifting inserts.
h. Install baulk ring and then install clutch gear and mainshaft rear
bearing.
Place wooden block under mainshaft in order to protect main-
shaft front bearing.
i.
Install spacer.
j.
Select snap ring with proper thickness and install it.
Allowable clearance between snap ring and groove:
0 - 0.15 mm (0 - 0.0059 in)
Available snap ring
Thickness
mm (in)
Part number
1.8 (0.071)
1.9 (0.075)
2.0 (0.079)
2.1 (0.083)
2.2 (0.087)
33138-73P20
33138-73P21
33138-73P22
33138-73P23
33138-73P24
SMT412A
SMT353A
SMT413A
SMT414A
ASSEMBLY
TF-30
k. Install steel ball, speedometer drive gear and retainer ring.
Steel ball is the smallest of check balls for this unit.
l.
Install low gear and its bearing to mainshaft.
Apply gear oil to needle bearing.
m. Install L & H hub and snap ring to mainshaft.
Pay special attention to direction of L & H hub.
n. Measure end play of low gear.
Standard:
0 - 0.15 mm (0 - 0.0059 in)
6. Apply sealant to mating surface and put center case assembly
onto front case and tighten bolts.
SMT415A
SMT340A
SMT760A
YMT017
SMT343A
ASSEMBLY
TF-31
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст