Nissan Murano Z51. Instruction — part 465
DLK-368
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY RECEIVER
REMOTE KEYLESS ENTRY RECEIVER
Exploded View
INFOID:0000000005517851
Removal and Installation
INFOID:0000000005517852
REMOVAL
1.
Remove the instrument lower panel RH. Refer to
IP-13, "Removal and Installation"
2.
Remove the remote keyless entry receiver mounting bolt (A),
and then remove remote keyless entry receiver (1).
INSTALLATION
Install in the reverse order of removal.
1.
Remote keyless entry receiver
JMKIA2178ZZ
JMKIA2171ZZ
INTELLIGENT KEY BATTERY
DLK-369
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY BATTERY
Removal and Installation
INFOID:0000000005517853
1.
Release the lock knob at the back of the Intelligent Key and remove the mechanical key.
2.
Insert a flat-blade screwdriver (A) wrapped with a cloth into the
slit of the corner and twist it to separate the upper part from the
lower part.
CAUTION:
• Do not touch the circuit board or battery terminal.
• The key fob is water-resistant. However, if it does get wet,
immediately wipe it dry.
3.
Replace the battery with new one.
4.
Align the tips of the upper and lower parts, and then push them
together until it is securely closed.
CAUTION:
• When replacing battery, keep dirt, grease, and other for-
eign materials off the electrode contact area.
• After replacing the battery, check that all Intelligent Key
functions work normally.
PIIB6221E
Battery replacement
:Coin-type lithium battery
(CR2025)
PIIB6222E
DLK-370
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
AUTOMATIC BACK DOOR CONTROL UNIT
AUTOMATIC BACK DOOR CONTROL UNIT
Exploded View
INFOID:0000000005517854
Removal and Installation
INFOID:0000000005517855
REMOVAL
1.
Remove the luggage side finisher lower (RH). Refer to
INT-35, "Removal and Installation"
.
2.
Remove the automatic back door control unit bracket mounting
bolt (A) and nats (B), and then remove the automatic back door
control unit bracket.
3.
Remove the automatic back door control unit mounting bolt, and then remove the automatic back door
control unit.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installing back door control unit, perform additional service when replace control unit. Refer to
"ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement"
1.
Automatic back door control unit
2.
Automatic back door control unit bracket
JMKIA2125ZZ
JMKIA2124ZZ
AUTOMATIC BACK DOOR WARNING BUZZER
DLK-371
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
AUTOMATIC BACK DOOR WARNING BUZZER
Exploded View
INFOID:0000000005517856
.
Removal and Installation
INFOID:0000000005517857
REMOVAL
1.
Remove the rear bumper. Refer to
EXT-16, "Removal and Installation"
.
2.
Remove the automatic back door warning buzzer mounting nut
(A), and then remove the automatic back door warning buzzer
(1).
INSTALLATION
Install in the reverse order of removal.
JMKIA2123ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст