Nissan Murano Z51. Instruction — part 328
BODY CONSTRUCTION
BRM-19
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
BODY CONSTRUCTION
Body Construction
INFOID:0000000005513908
1.
Outer side body
2.
Upper front pillar reinforcement
3.
Upper inner front pillar
4.
Upper front pillar hinge brace
5.
Hoodledge reinforcement
6.
Side dash
7.
Upper dash
8.
Lower dash
9.
Side cowl top brace
JSKIA0575ZZ
BRM-20
< UNIT REMOVAL AND INSTALLATION >
BODY CONSTRUCTION
10. Weld nut
11.
Lower front pillar hinge brace
12. Lower front pillar patch
13. Front fender bracket
14. Outer front sill reinforcement
15. Lower front pillar reinforcement
16. Inner front sill reinforcement
17. Front side member outrigger
18. Front floor
19. Outer sill reinforcement
20. Inner sill
21. Inner rear sill reinforcement
22. 2nd crossmember
23. Center pillar reinforcement
24. Center pillar seat belt reinforcement
25. Inner center pillar reinforcement
26. Inner center pillar
27. 3rd crossmember
28. Seat belt anchor
29. Inner sill extension
30. Inner rear pillar reinforcement
31. Inner rear pillar seat belt anchor
32. Inner rear pillar
33. Outer rear wheelhouse
34. Inner rear wheelhouse
35. Outer back pillar
36. Back pillar reinforcement
37. Rear roof rail brace
38. Back pillar main
REPLACEMENT OPERATIONS
BRM-21
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
REPLACEMENT OPERATIONS
Description
INFOID:0000000005513909
• This section is prepared for technicians who have attained a high level of skill and experience in repairing
collision-damaged vehicles and also use modern service tools and equipment. Persons unfamiliar with body
repair techniques should not attempt to repair collision-damaged vehicles by using this section.
• Technicians are also encouraged to read the Body Repair Instruction (Fundamentals) in order to ensure that the
original functions and quality of the vehicle are maintained. The Body Repair Instruction (Fundamentals) con-
tains additional information, including cautions and warnings, that are not including in this instruction. Techni-
cians should refer to both instructions to ensure proper repair.
• Please note that this information is prepared for worldwide usage, and as such, certain procedures might not
apply in some regions or countries.
The symbols used in this section for welding operations are shown below.
Symbol marks
Description
2-spot welds
3-spot welds
MIG plug weld
For 3 panels plug weld method
MIG seam weld / Point weld
JSKIA0049ZZ
JSKIA0053ZZ
JSKIA0050ZZ
JSKIA0051ZZ
JSKIA0054ZZ
JSKIA0055ZZ
JSKIA0052ZZ
JSKIA0056ZZ
BRM-22
< UNIT REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
• Front pillar butt joint can be determined anywhere within shaded
area as shown in the figure. The best location for the butt joint is at
position A due to the construction of the vehicle.
• Determine cutting position and record distance from the locating
indent. Use this distance when cutting the service part. Cut outer
front pillar over 60 mm (2.36 in) above the inner front pillar cut
position.
• Prepare a cutting jig to make outer pillar easier to cut. Also, this will
permit the service part to be accurately cut at the joint position.
• An example of cutting operation using a cutting jig is as per the fol-
lowing.
1.
Mark cutting lines.
A: Cut position of outer pillar
B: Cut position of inner pillar
2.
Align cutting line with notch on jig. Clamp jig to pillar.
3.
Cut outer pillar along groove of jig (at position A).
4.
Remove jig and cut remaining portions.
5.
Cut inner pillar at position B in same manner.
PIIA0150E
JSKIA0104GB
JSKIA0105GB
PIIA0153E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст