Nissan Murano Z51. Instruction — part 480
DLN-54
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: TY20A]
TRANSFER ASSEMBLY
UNIT REMOVAL AND INSTALLATION
TRANSFER ASSEMBLY
Exploded View
INFOID:0000000005514212
Removal and Installation
INFOID:0000000005514213
REMOVAL
1.
Remove extension cowl top panel (lower and upper). Refer to
2.
Remove battery and battery tray.
3.
Remove air duct (inlet), air cleaner case (upper and lower) with mass air flow sensor and air duct assem-
bly. Refer to
.
4.
Remove air fuel ratio sensor 1 (bank 1). Refer to
.
5.
Remove front road wheel and tires.
6.
Remove splash guards (RH and LH).
7.
Remove engine under cover.
8.
Remove air guide.
9.
Remove front drive shaft (right side). Refer to
.
CAUTION:
Be careful not to damage gear ring oil seal inside of transfer.
10. Remove exhaust front tube. Refer to
11. Separate the rear propeller shaft. Refer to
.
12. Disconnect oxygen sensor 2 (bank 1) harness connector.
13. Remove heat insulator from front suspension member.
14. Remove three way catalyst (bank 1). Refer to
CAUTION:
Handle carefully to avoid any shock to three way catalyst.
15. Remove power steering tube brackets from front suspension member.
16. Remove high pressure piping and low pressure hose from power steering gear. Refer to
.
1.
Transfer assembly
2.
Transfer gusset
3.
Rear gusset
: Vehicle front
Refer to
for symbols not described on the above.
JSDIA1107GB
TRANSFER ASSEMBLY
DLN-55
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: TY20A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
CAUTION:
Never let the power steering fluid into the suspension member.
17. Remove rear engine mounting insulator mounting bolt (upper side). Refer to
.
18. Support transaxle assembly with a suitable jack.
CAUTION:
When setting the transmission jack, be careful not to allow it to collide against the drain plug.
19. Support front suspension member with a suitable jack.
20. Remove rear gusset and transfer gusset.
21. Remove rear engine mounting insulator mounting bolt (lower side). Refer to
.
22. Disconnect front and rear engine mounting insulator harness connector and harness clip.
23. Move rear engine mounting insulator to remove rear engine mounting bracket.
CAUTION:
Never damage power steering gear boot.
24. Remove rear engine mounting bracket. Refer to
25. Remove LH and RH engine mounting bracket. Refer to
26. Remove member stay, front suspension member fixing bolts and nuts. Refer to
.
27. Lower the jack for the front suspension member to the height where the transfer assembly can be
removed.
28. Remove bolts fitting transaxle assembly and transfer assembly.
29. Remove transfer assembly from the vehicle.
CAUTION:
• Never damage air breather hose.
• After removing transfer from transaxle, be sure to replace
differential side oil seal of the transaxle side with new
one. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
• When installing the transfer to the transaxle, install the mounting
bolts following the standard below.
CAUTION:
When installing transfer to transaxle, be careful not to dam-
age oil seal of transaxle.
• Check oil level and check for oil leakage after installation. Refer to
.
Bolt No.
1
2
Quantity
4
2
Bolt length “
” mm (in)
65 (2.56)
40 (1.57)
SDIA1510E
Bolt No.
1
2
Quantity
4
2
Bolt length “
” mm (in)
65 (2.56)
40 (1.57)
SDIA1510E
DLN-56
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY20A]
ADAPTER CASE
UNIT DISASSEMBLY AND ASSEMBLY
ADAPTER CASE
Exploded View
INFOID:0000000005514214
1.
Pinion lock nut
2.
Companion flange
3.
Pinion sleeve oil seal
4.
Pinion rear bearing
5.
Dust cover
6.
Pinion sleeve
7.
O-ring
8.
Collapsible spacer
9.
Pinion front bearing
10. Drive pinion
11.
Pinion sleeve shim
12. Adapter case oil seal
13. Drain plug
14. Adapter case
15. Oil gutter
16. O-ring
17. Gear ring bearing adjusting shim
(adapter case side)
18. Gear ring bearing
(adapter case side)
19. Gear ring oil seal
20. Gear ring
21. Drive gear
22. Gear ring bearing
(transfer case side)
23. Gear ring bearing adjusting shim
(transfer case side)
24. Oil defense
25. Filler plug
26. Transfer case oil seal
27. Transfer case
JPDIE0022GB
ADAPTER CASE
DLN-57
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY20A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Disassembly
INFOID:0000000005514215
1.
Remove adapter case mounting bolts (
).
2.
Lightly tap adapter case with a plastic hammer to remove
adapter case.
3.
Remove O-ring from adapter case.
4.
Remove adapter case oil seal with a suitable tool.
CAUTION:
Be careful not to damage adapter case.
28. Breather tube
29. Plug
A. Oil seal lip
B. Screw hole
C. For the tightening torque, refer to
.
: Apply gear oil.
: Apply multi-purpose grease.
: Apply Genuine Silicone RTV or equivalent. Refer to
GI-18, "Recommended Chemical Products and Sealants"
.
: Apply Genuine High Strength Thread Locking Sealant or equivalent. Refer to
GI-18, "Recommended Chemical Products
Refer to
for symbols not described above.
SDIA1528E
SDIA1529E
SDIA1530E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст