Nissan Murano Z51. Instruction — part 558
EC-240
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P0197, P0198 EOT SENSOR
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005536640
1.
CHECK GROUND CONNECTION
1.
Turn ignition switch OFF.
2.
Check ground connection E38. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
2.
CHECK EOT SENSOR POWER SUPPLY CIRCUIT
1.
Disconnect engine oil temperature (EOT) sensor harness connector.
2.
Turn ignition switch ON.
3.
Check the voltage between EOT sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
3.
CHECK EOT SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between EOT sensor harness connector and ECM harness connector.
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
4.
CHECK ENGINE OIL TEMPERATURE SENSOR
EC-240, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace engine oil temperature sensor.
5.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000005536641
1.
CHECK ENGINE OIL TEMPERATURE SENSOR
1.
Turn ignition switch OFF.
2.
Disconnect engine oil temperature sensor harness connector.
3.
Remove engine oil temperature sensor.
EOT sensor
Ground
Voltage
Connector
Terminal
F66
1
Ground
Approx. 5 V
EOT sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F66
2
F8
52
Existed
P0197, P0198 EOT SENSOR
EC-241
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
4.
Check resistance between engine oil temperature sensor termi-
nals by heating with hot water as shown in the figure.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace engine oil temperature sensor.
Terminals
Condition
Resistance
1 and 2
Temperature [
°
C (
°
F)]
20 (68)
2.1 - 2.9 k
Ω
50 (122)
0.68 - 1.00 k
Ω
90 (194)
0.236 - 0.260 k
Ω
JMBIA0080ZZ
EC-242
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P0222, P0223 TP SENSOR
P0222, P0223 TP SENSOR
Description
INFOID:0000000005536642
Electric throttle control actuator consists of throttle control motor,
throttle position sensor, etc. The throttle position sensor responds to
the throttle valve movement.
The throttle position sensor has two sensors. These sensors are a
kind of potentiometer which transform the throttle valve position into
output voltage, and emit the voltage signals to the ECM. The ECM
judges the current opening angle of the throttle valve from these sig-
nals and controls the throttle valve opening angle in response to
driving conditions via the throttle control motor.
DTC Logic
INFOID:0000000005536643
DTC DETECTION LOGIC
NOTE:
If DTC P0222 or P0223 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and let it idle for 1 second.
2.
Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005536644
1.
CHECK GROUND CONNECTION
1.
Turn ignition switch OFF.
2.
Check ground connection E38. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
PBIB0145E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0222
Throttle position sensor
1 circuit low input
An excessively low voltage from the TP sensor
1 is sent to ECM.
• Harness or connectors
(TP sensor 1 circuit is open or shorted.)
• Electric throttle control actuator
(TP sensor 1)
P0223
Throttle position sensor
1 circuit high input
An excessively high voltage from the TP sensor
1 is sent to ECM.
P0222, P0223 TP SENSOR
EC-243
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2.
CHECK THROTTLE POSITION SENSOR 1 POWER SUPPLY CIRCUIT-I
1.
Disconnect electric throttle control actuator harness connector.
2.
Turn ignition switch ON.
3.
Check the voltage between electric throttle control actuator harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
3.
CHECK THROTTLE POSITION SENSOR 1 GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between electric throttle control actuator and ECM harness connector.
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
4.
CHECK THROTTLE POSITION SENSOR 1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check the continuity between electric throttle control actuator and ECM harness connector.
2.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
5.
CHECK THROTTLE POSITION SENSOR
EC-244, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 6.
6.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace electric throttle control actuator.
2.
EC-244, "Special Repair Requirement"
>> INSPECTION END
7.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
.
>> INSPECTION END
Electric throttle control actuator
Ground
Voltage
Connector
Terminal
F29
1
Ground
Approx. 5 V
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F29
4
F8
36
Existed
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F29
2
F8
37
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст