Nissan Murano Z51. Instruction — part 53
ADP-204
< SYMPTOM DIAGNOSIS >
INTELLIGENT KEY INTERLOCK FUNCTION DOES NOT OPERATE
INTELLIGENT KEY INTERLOCK FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000005515438
1.
CHECK DOOR LOCK FUNCTION
Check door lock function.
Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunction parts.
2.
PERFORM MEMORY STORING PROCEDURE
1.
Perform memory storing procedure.
Refer to
ADP-10, "MEMORY STORING : Special Repair Requirement"
2.
Check Intelligent Key interlock function.
Refer to
ADP-34, "INTELLIGENT KEY INTERLOCK FUNCTION : System Description"
.
Is the inspection result normal?
YES
>> Intelligent Key inter lock function is normal.
NO
>> Replace driver seat control unit. Refer to
ALL COMPONENTS OF TILT & TELESCOPIC SWITCH DO NOT OPERATE
ADP-205
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
ALL COMPONENTS OF TILT & TELESCOPIC SWITCH DO NOT OPERATE
Diagnosis Procedure
INFOID:0000000005515439
1.
CHECK TILT & TELESCOPIC SWITCH GROUND CIRCUIT
Check tilt & telescopic switch ground circuit.
Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connector.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
NO
>> GO TO 1.
ADP-206
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000005515440
The following symptoms are normal operations, and they do not indicate a malfunction.
Symptom
Cause
Action to take
Reference page
Entry/exit assist function and
seat synchronization do not op-
erate.
No initialization has been performed.
Perform initialization.
Entry/exit assist function is disabled.
NOTE:
The entry/exit assist function and seat
synchronization function are disabled be-
fore delivery (initial setting).
Change the settings.
Entry assist function does not op-
erate.
Instruction operation with power seat switch
was performed after exit assist function
execution.
Perform the memory
function.
Lumbar support does not per-
form memory operation.
The lumbar support system are con-
trolled independently with no link to the
automatic drive positioner system.
—
Lumbar support system:
Memory function, entry/exit as-
sist function, or Intelligent Key in-
terlock function does not
operate.
The operating conditions are not fulfilled.
Fulfill the operation
conditions.
Memory function:
Exit assist function:
Entry assist function:
Intelligent Key interlock
function:
PRECAUTIONS
ADP-207
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
PRECAUTION
PRECAUTIONS
FOR USA AND CANADA
FOR USA AND CANADA : Precaution for Supplemental Restraint System (SRS) "AIR
BAG" and "SEAT BELT PRE-TENSIONER"
INFOID:0000000005716216
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
FOR MEXICO
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER"
INFOID:0000000005716220
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст