Nissan Murano Z51. Instruction — part 1209
SE-24
< DTC/CIRCUIT DIAGNOSIS >
REAR POWER RETURN SWITCH
NO
>> Replace rear power return switch (RH). Refer to
SE-139, "Removal and Installation"
.
PRIMARY POSITION LIMIT SWITCH
SE-25
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
PRIMARY POSITION LIMIT SWITCH
LH
LH : Description
INFOID:0000000005518163
Detect the initial position of sector gear (LH).
LH : Component Function Check
INFOID:0000000005518164
1.
CHECK FUNCTION
Check that the rear seatback (LH) rises when pressing and holding the power return switch (LH).
Is the inspection result normal?
YES
>> Primary position limit switch (LH) is OK.
NO
>> Refer to
SE-25, "LH : Diagnosis Procedure"
LH : Diagnosis Procedure
INFOID:0000000005518165
1.
CHECK REAR SEATBACK POWER RETURN CONTROL UNIT OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect primary position limit switch (LH) connector.
3.
Check voltage between primary position limit switch (LH) connector and ground.
NOTE:
It is not low power consumption mode.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK PRIMARY POSITION LIMIT SWITCH (LH) SIGNAL CIRCUIT
1.
Disconnect rear seatback power return control unit connector.
2.
Check continuity between rear seatback power return control unit harness connector and primary position
limit switch (LH) harness connector.
3.
Check continuity between rear seatback power return control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear seatback power return control unit. Refer to
SE-133, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK PRIMARY POSITION LIMIT SWITCH (LH) GROUND CIRCUIT
1.
Check continuity between rear seatback power return control unit harness connector and primary position
limit switch (LH) harness connector.
(+)
(–)
Voltage (V)
(Approx.)
Primary position limit switch (LH)
Connector
Terminal
B499
1
Ground
Battery voltage
Rear seatback power return control unit
Primary position limit switch (LH)
Continuity
Connector
Terminal
Connector
Terminal
B493
21
B499
1
Existed
Rear seatback power return control unit
Ground
Continuity
Connector
Terminal
B493
21
Not existed
SE-26
< DTC/CIRCUIT DIAGNOSIS >
PRIMARY POSITION LIMIT SWITCH
2.
Check continuity between rear seatback power return control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK PRIMARY POSITION LIMIT SWITCH (LH)
Check primary position limit switch (LH).
Refer to
SE-26, "LH : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace primary position limit switch (LH) [reclining device assembly (LH)]. Refer to
.
5.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
>> INSPECTION END
LH : Component Inspection
INFOID:0000000005518166
COMPONENT INSPECTION
1.
CHECK PRIMARY POSITION LIMIT SWITCH (LH)
1.
Turn ignition switch OFF.
2.
Disconnect primary position limit switch (LH) connector.
3.
Check primary position limit switch (LH) terminals.
Is the inspection result normal?
YES
>> Primary position limit switch (LH) is OK.
NO
>> Replace primary position limit switch (LH) [reclining device assembly (LH)]. Refer to
.
RH
RH : Description
INFOID:0000000005518167
Detect the initial position of sector gear (RH).
RH : Component Function Check
INFOID:0000000005518168
1.
CHECK FUNCTION
Check that the rear seatback (RH) rises when pressing and holding the power return switch (RH).
Is the inspection result normal?
YES
>> Primary position limit switch (RH) is OK.
NO
>> Refer to
SE-27, "RH : Diagnosis Procedure"
.
Rear seatback power return control unit
Primary position limit switch (LH)
Continuity
Connector
Terminal
Connector
Terminal
B493
31
B499
2
Existed
Rear seatback power return control unit
Ground
Continuity
Connector
Terminal
B493
31
Not existed
Primary position limit switch (LH) connector
Terminal
Condition
Continuity
B499
1
2
Primary position limit switch (LH) is pressed
Existed
Primary position limit switch (LH) is released
Not existed
PRIMARY POSITION LIMIT SWITCH
SE-27
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
RH : Diagnosis Procedure
INFOID:0000000005518169
1.
CHECK REAR SEATBACK POWER RETURN CONTROL UNIT OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect primary position limit switch (RH) connector.
3.
Check voltage between primary position limit switch (RH) harness connector and ground.
NOTE:
It is not low power consumption mode.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK PRIMARY POSITION LIMIT SWITCH (RH) SIGNAL CIRCUIT
1.
Disconnect rear seatback power return control unit connector.
2.
Check continuity between rear seatback power return control unit harness connector and primary position
limit switch (RH) harness connector.
3.
Check continuity between rear seatback power return control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear seatback return control unit. Refer to
SE-133, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK PRIMARY POSITION LIMIT SWITCH (RH) GROUND CIRCUIT
1.
Check continuity between rear seatback power return control unit harness connector and primary position
limit switch (RH) harness connector.
2.
Check continuity between rear seatback power return control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK PRIMARY POSITION LIMIT SWITCH (RH)
Check primary position limit switch (RH).
Refer to
SE-28, "RH : Component Inspection"
(+)
(–)
Voltage (V)
(Approx.)
Primary position limit switch (RH)
Connector
Terminal
B495
1
Ground
Battery voltage
Rear seatback power return control unit
Primary position limit switch (RH)
Continuity
Connector
Terminal
Connector
Terminal
B493
22
B495
1
Existed
Rear seatback power return control unit
Ground
Continuity
Connector
Terminal
B493
22
Not existed
Rear seatback power return control unit
Primary position limit switch (RH)
Continuity
Connector
Terminal
Connector
Terminal
B493
23
B495
2
Existed
Rear seatback power return control unit
Ground
Continuity
Connector
Terminal
B493
23
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст