Nissan Murano Z51. Instruction — part 29
ADP-108
< DTC/CIRCUIT DIAGNOSIS >
TILT MOTOR
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-210, "Removal and Installation"
NO
>> Repair or replace harness or connector.
Automatic drive positioner control unit
Tilt motor
Continuity
Connector
Terminal
Connector
Terminal
M104
28
M116
1
Existed
29
2
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M104
28
Not existed
29
TELESCOPIC MOTOR
ADP-109
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
TELESCOPIC MOTOR
Description
INFOID:0000000005515405
• The telescopic motor is installed to the steering column assembly.
• The telescopic motor is activated with the automatic drive positioner control unit.
• Compresses the steering column by changing the rotation direction of telescopic motor.
Component Function Check
INFOID:0000000005515406
1.
CHECK FUNCTION
1.
Select “TELESCO MOTOR” in “Active test” mode with CONSULT-III.
2.
Check the telescopic motor operation.
Is the operation of relevant parts normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
ADP-109, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000005515407
1.
CHECK TELESCOPIC MOTOR POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect telescopic motor connector.
3.
Turn the ignition switch ON.
4.
Perform “Active test” (“TELESCO MOTOR”) with CONSULT-lll
5.
Check voltage between telescopic motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace telescopic motor. (Built in steering column assembly.)
NO
>> GO TO 2.
2.
CHECK TELESCOPIC MOTOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit.
3.
Check continuity between automatic drive positioner control unit harness connector and telescopic motor
harness connector.
Test item
Description
TELESCO MOTOR
OFF
Steering telescopic
Stop
FR Forward
RR
Backward
(+)
(–)
Condition
Voltage (V)
(Approx.)
Telescopic motor
Connector
Terminals
M117
1
Ground
TELESCOPIC MO-
TOR
OFF
0
FR (forward)
0
RR (backward)
Battery voltage
2
OFF
0
FR (forward)
Battery voltage
RR (backward)
0
ADP-110
< DTC/CIRCUIT DIAGNOSIS >
TELESCOPIC MOTOR
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-210, "Removal and Installation"
NO
>> Repair or replace harness or connector.
Automatic drive positioner control unit
Telescopic motor
Continuity
Connector
Terminal
Connector
Terminal
M75
29
M117
2
Existed
26
1
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
29
Not existed
26
DOOR MIRROR MOTOR
ADP-111
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
DOOR MIRROR MOTOR
Description
INFOID:0000000005515408
It makes mirror face operate from side to side and up and down with the electric power that AUTOMATIC
DRIVE POSITIONER CONTROL UNIT supplies.
Component Function Check
INFOID:0000000005515409
1.
CHECK DOOR MIRROR MOTOR FUNCTION
Check the operation with “MIRROR MOTOR RH” and “MIRROR MOTOR LH” in “ACTIVE TEST” mode with
CONSULT-III
Refer to
ADP-38, "CONSULT-III Function"
.
Is the inspection result normal?
YES
>> Door mirror motor function is OK.
NO
>> Refer to
ADP-111, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000005515410
1.
CHECK DOOR MIRROR MOTOR INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between door mirror connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR MIRROR MOTOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector and door mirror connector.
3.
Check continuity between automatic drive positioner control unit connector and door mirror connector.
[Door mirror driver side]
[Door mirror passenger side]
(+)
(–)
Condition
Voltage (V)
(Approx.)
Door mirror
Connector
Terminals
D3 (Driver side)
D43 (Passenger side)
12
Ground
Door mirror remote
control switch
UP
Battery voltage
Other than above
0
11
LEFT
Battery voltage
Other than above
0
10
DOWN / RIGHT
Battery voltage
Other than above
0
Automatic drive positioner control unit
Door mirror (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M75
12
D3
10
Existed
23
12
24
11
Automatic drive positioner control unit
Door mirror (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M75
22
D43
10
Existed
10
12
11
11
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст