Nissan Murano Z51. Instruction — part 1537
WW-26
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
BCM (BODY CONTROL MODULE)
BCM (BODY CONTROL MODULE) : Diagnosis Procedure
INFOID:0000000005516011
1.
CHECK FUSE AND FUSIBLE LINK
Check that the following fuse and fusible link are not blown.
Is the fuse fusing?
YES
>> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is
blown.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connectors.
3.
Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) : Di-
agnosis Procedure
INFOID:0000000005516012
1.
CHECK FUSES AND FUSIBLE LINK
Check that the following IPDM E/R fuses or fusible links are not blown.
Signal name
Fuse and fusible link No.
Battery power supply
L
10
Terminals
Voltage
(Approx.)
(+)
(
−
)
BCM
Ground
Connector
Terminal
M118
1
Battery voltage
M119
11
BCM
Ground
Continuity
Connector
Terminal
M119
13
Existed
POWER SUPPLY AND GROUND CIRCUIT
WW-27
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Is the fuse fusing?
YES
>> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is
blown.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check voltage between IPDM E/R harness connector and the ground.
Is the measurement value normal?
YES
>> GO TO 3.
NO
>> Repair the harness or connector.
3.
CHECK GROUND CIRCUIT
Check continuity between IPDM E/R harness connectors and the ground.
Does continuity exist?
YES
>> INSPECTION END
NO
>> Repair the harness or connector.
Signal name
Fuses and fusible link No.
Battery power supply
E
50
51
Terminals
Voltage
(Approx.)
(+)
(
−
)
IPDM E/R
Connector
Terminal
Ground
E9
1
Battery voltage
IPDM E/R
Ground
Continuity
Connector
Terminal
E10
12
Existed
E11
41
WW-28
< DTC/CIRCUIT DIAGNOSIS >
FRONT WIPER MOTOR LO CIRCUIT
FRONT WIPER MOTOR LO CIRCUIT
Component Function Check
INFOID:0000000005516013
1.
CHECK FRONT WIPER LO OPERATION
IPDM E/R AUTO ACTIVE TEST
1.
Start IPDM E/R auto active test. Refer to
PCS-10, "Diagnosis Description"
2.
Check that the front wiper operates at the LO operation.
CONSULT-III ACTIVE TEST
1.
Select “FRONT WIPER” of IPDM E/R active test item.
2.
With operating the test item, check front wiper operation.
Is front wiper (LO) operation normally?
YES
>> Front wiper motor LO circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000005516014
1.
CHECK FRONT WIPER MOTOR (LO) OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1.
Turn the ignition switch OFF.
2.
Disconnect front wiper motor connector.
3.
Turn the ignition switch ON.
4.
Select “FRONT WIPER” of IPDM E/R active test item.
5.
With operating the test item, check voltage between IPDM E/R harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 2.
NO
>> Replace IPDM E/R.
2.
CHECK FRONT WIPER MOTOR (LO) OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
Does continuity exist?
YES
>> GO TO 3.
NO
>> Repair the harness or connector.
3.
CHECK FRONT WIPER MOTOR (LO) SHORT CIRCUIT
Check continuity between IPDM E/R harness connector and ground.
Lo
: Front wiper (LO) operation
Off
: Stop the front wiper.
Terminals
Test item
Voltage (Approx.)
(+)
(
−
)
IPDM E/R
Ground
FRONT WIPER
Connector
Terminal
E10
4
Lo
Battery voltage
Off
0 V
IPDM E/R
Front wiper motor
Continuity
Connector
Terminal
Connector
Terminal
E10
4
E12
1
Existed
FRONT WIPER MOTOR LO CIRCUIT
WW-29
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Does continuity exist?
YES
>> Repair the harness or connector.
NO
>> Replace front wiper motor.
IPDM E/R
Ground
Continuity
Connector
Terminal
E10
4
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст