Nissan Murano Z51. Instruction — part 1029
MIR-72
< REMOVAL AND INSTALLATION >
[WITH ADP]
OUTSIDE MIRROR
DOOR MIRROR ASSEMBLY : Removal and Installation
INFOID:0000000005513430
CAUTION:
Never damage the mirror bodies.
REMOVAL
1.
Remove the front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
2.
Remove the door mirror corner cover.
3.
Disconnect the door mirror harness connector.
4.
Remove the door mirror mounting nuts, and remove the door mirror assembly.
INSTALLATION
Install in the reverse order of removal.
GLASS MIRROR
GLASS MIRROR : Exploded View
INFOID:0000000005513431
GLASS MIRROR : Disassembly and Assembly
INFOID:0000000005513432
CAUTION:
Never damage the mirror bodies.
DISASSEMBLY
1.
Door mirror cover
2.
Door mirror assembly
3.
Glass mirror
: Pawl
1.
Door mirror cover
2.
Door mirror assembly
3.
Glass mirror
: Pawl
JMLIA0123ZZ
OUTSIDE MIRROR
MIR-73
< REMOVAL AND INSTALLATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
1.
Place the glass mirror upward.
2.
Put a strip of protective tape (A) on the housing.
3.
Insert flat-bladed screwdriver (B) into the recess at lower side
between glass mirror (1) and actuator (2), and push up pawls to
remove glass mirror lower side.
NOTE:
Insert a small slotted screwdriver into recess, and push up while
rotating (twist) to make work easier.
4.
Insert flat-bladed screwdriver at RH/LH side between glass mirror and actuator, and push up pawls to
remove glass mirror RH/LH side.
NOTE:
Insert flat-bladed screwdriver into recesses, and push up while rotating (twist) to make work easier.
5.
Remove two terminals of mirror heater attachment. (With heater mirror model)
6.
Pull glass mirror as shown in the figure in order to disengage
both upper pawls, and then remove glass mirror.
ASSEMBLY
Install in the reverse order of removal.
CAUTION:
After installation, visually check that pawls are securely engaged.
DOOR MIRROR COVER
JMLIA0124ZZ
1.
Glass mirror
2.
Actuator
JMLIA0092ZZ
MIR-74
< REMOVAL AND INSTALLATION >
[WITH ADP]
OUTSIDE MIRROR
DOOR MIRROR COVER : Exploded View
INFOID:0000000005513433
DOOR MIRROR COVER : Disassembly and Assembly
INFOID:0000000005513434
CAUTION:
Never damage the mirror bodies.
DISASSEMBLY
1.
Remove the glass mirror. Refer to
MIR-72, "GLASS MIRROR : Disassembly and Assembly"
2.
Remove the pawls, and disassemble the door mirror cover from the mirror assembly.
ASSEMBLY
Install in the reverse order of removal.
NOTE:
After installation, visually check that pawls are securely engaged.
1.
Door mirror cover
2.
Door mirror assembly
3.
Glass mirror
: Pawl
JMLIA0123ZZ
DOOR MIRROR REMOTE CONTROL SWITCH
MIR-75
< REMOVAL AND INSTALLATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DOOR MIRROR REMOTE CONTROL SWITCH
Exploded View
INFOID:0000000005513435
INT-12, "FRONT DOOR FINISHER : Exploded View"
Removal and Installation
INFOID:0000000005513436
REMOVAL
1.
Remove the power window main switch finisher (2). Refer to
PWC-119, "Removal and Installation"
2.
Remove door mirror remote control switch (1) from power win-
dow main switch finisher (2) using flat-bladed screwdriver (A).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMLIA0118ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст