Nissan Murano Z51. Instruction — part 1293
PRECAUTIONS
SEC-219
< PRECAUTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
FOR MEXICO : Precaution for Procedure without Cowl Top Cover
INFOID:0000000005716233
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
FOR MEXICO : Precaution Necessary for Steering Wheel Rotation after Battery Dis-
connect
INFOID:0000000005716230
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT-III.
PIIB3706J
SEC-220
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
KEY SLOT
REMOVAL AND INSTALLATION
KEY SLOT
Exploded View
INFOID:0000000005515657
Removal and Installation
INFOID:0000000005515658
REMOVAL
1.
Remove the instrument lower panel LH (2). Refer to
2.
Disconnect key slot connector.
3.
Remove the key slot mounting screw (A), and then remove key
slot (1) from instrument lower panel LH (2).
INSTALLATION
Install in the reverse order of removal.
1.
Key slot
2.
Instrument lower panel LH
JMKIA1820ZZ
JMKIA1821ZZ
PUSH BUTTON IGNITION SWITCH
SEC-221
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
PUSH BUTTON IGNITION SWITCH
Exploded View
INFOID:0000000005515659
Removal and Installation
INFOID:0000000005515660
REMOVAL
1.
Remove the instrument stay cover LH. Refer to
IP-13, "Removal and Installation"
.
2.
Remove the push-button ignition switch (1) from instrument stay
cover LH, after removing pawl (A). Press push-button ignition
switch (1) back to disengage from instrument stay cover LH (2).
INSTALLATION
Install in the reverse order of removal.
1.
Push-button ignition switch
JMKIA1812ZZ
JMKIA1813ZZ
SEC-222
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
SECURITY INDICATOR LAMP
SECURITY INDICATOR LAMP
Exploded View
INFOID:0000000005515661
Removal and Installation
INFOID:0000000005515662
REMOVAL
Remove the security indicator lamp (1).
•
Disengage pawls with tool (A) and pull up the security indica-
tor lamp.
INSTALLATION
Install in the reverse order of removal.
1.
Security indicator lamp
JMKIA1830ZZ
: Pawl
JMKIA1831ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст