Nissan Murano Z51. Instruction — part 602
EC-416
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P2135 TP SENSOR
>> INSPECTION END
Component Inspection
INFOID:0000000005536840
1.
CHECK THROTTLE POSITION SENSOR
1.
Turn ignition switch OFF.
2.
Reconnect all harness connectors disconnected.
3.
EC-416, "Special Repair Requirement"
4.
Turn ignition switch ON.
5.
Shift selector lever position to D.
6.
Check the voltage between ECM harness connector terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace electric throttle control actuator.
2.
Go to
EC-416, "Special Repair Requirement"
.
>> INSPECTION END
Special Repair Requirement
INFOID:0000000005536841
1.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
EC-18, "THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement"
>> GO TO 2.
2.
PERFORM IDLE AIR VOLUME LEARNING
EC-18, "IDLE AIR VOLUME LEARNING : Special Repair Requirement"
>> END
ECM
Condition
Voltage
+
–
Connector
Terminal
Connector
Terminal
F8
37
(TP sensor 1 signal)
F8
36
(Sensor ground)
Accelerator pedal
Fully released
More than 0.36 V
Fully depressed
Less than 4.75 V
38
(TP sensor 2 signal)
Fully released
Less than 4.75 V
Fully depressed
More than 0.36 V
P2138 APP SENSOR
EC-417
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P2138 APP SENSOR
Description
INFOID:0000000005536842
The accelerator pedal position sensor is installed on the upper end
of the accelerator pedal assembly. The sensor detects the accelera-
tor position and sends a signal to the ECM.
Accelerator pedal position sensor has two sensors. These sensors
are a kind of potentiometer which transform the accelerator pedal
position into output voltage, and emit the voltage signals to the ECM.
The ECM judges the current opening angle of the accelerator pedal
from these signals and controls the throttle control motor based on
these signals.
Idle position of the accelerator pedal is determined by the ECM
receiving the signal from the accelerator pedal position sensor. The
ECM uses this signal for engine operations such as fuel cut.
DTC Logic
INFOID:0000000005536843
DTC DETECTION LOGIC
NOTE:
If DTC P2138 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and let it idle for 1 second.
2.
Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
PBIB1741E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2138
Accelerator pedal posi-
tion sensor circuit range/
performance
Rationally incorrect voltage is sent to ECM
compared with the signals from APP sensor 1
and APP sensor 2.
• Harness or connector
(APP sensor 1 or 2 circuit is open or
shorted.)
[CKP sensor (POS) circuit is shorted.]
(Refrigerant pressure sensor circuit is
shorted.)
(EVAP control system pressure sensor
circuit is shorted.)
• Accelerator pedal position sensor
(APP sensor 1 or 2)
• Crankshaft position sensor (POS)
• EVAP control system pressure sensor
• Refrigerant pressure sensor
EC-418
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P2138 APP SENSOR
Diagnosis Procedure
INFOID:0000000005536844
1.
CHECK GROUND CONNECTION
1.
Turn ignition switch OFF.
2.
Check ground connection E38. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
2.
CHECK APP SENSOR 1 POWER SUPPLY CIRCUIT
1.
Disconnect accelerator pedal position (APP) sensor harness connector.
2.
Turn ignition switch ON.
3.
Check the voltage between APP sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
3.
CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-I
1.
Turn ignition switch ON.
2.
Check the voltage between APP sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 4.
4.
CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-II
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between APP sensor harness connector and ECM harness connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair open circuit.
5.
CHECK SENSOR POWER SUPPLY CIRCUIT
Check harness for short to power and short to ground, between the following terminals.
APP sensor
Ground
Voltage (V)
Connector
Terminal
E110
4
Ground
Approx. 5
APP sensor
Ground
Voltage (V)
Connector
Terminal
E110
5
Ground
Approx. 5
APP sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E110
5
E16
87
Existed
ECM
Sensor
Connector
Terminal
Name
Connector
Terminal
F8
72
Refrigerant pressure sensor
E300
1
76
CKP sensor (POS)
F20
1
P2138 APP SENSOR
EC-419
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair short to ground or short to power in harness or connectors.
6.
CHECK COMPONENTS
Check the following.
• Crankshaft position sensor (POS) (Refer to
EC-257, "Component Inspection"
• EVAP control system pressure sensor (Refer to
EC-296, "Component Inspection"
.)
• Refrigerant pressure sensor (Refer to
.)
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Replace malfunctioning components.
7.
CHECK APP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between APP sensor harness connector and ECM harness connector.
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
8.
CHECK APP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check the continuity between APP sensor harness connector and ECM harness connector.
2.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
9.
CHECK APP SENSOR
EC-420, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> GO TO 10.
10.
REPLACE ACCELERATOR PEDAL ASSEMBLY
1.
Replace accelerator pedal assembly.
2.
EC-420, "Special Repair Requirement"
E16
87
APP sensor
E110
5
91
EVAP control system pressure sensor
B17
3
ECM
Sensor
Connector
Terminal
Name
Connector
Terminal
APP sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E110
2
E16
84
Existed
1
100
APP sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E110
3
E16
81
Existed
6
82
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст