Nissan Murano Z51. Instruction — part 1247
P1610 LOCK MODE
SEC-35
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
P1610 LOCK MODE
Description
INFOID:0000000005515480
When the starting operation is carried more than five times consecutively under the following conditions, NATS
will shift to the mode which prevents the engine from being started.
• Unregistered Intelligent Key is used.
• BCM or ECM is malfunctioning.
DTC Logic
INFOID:0000000005515481
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005515482
1.
CHECK ENGINE START FUNCTION
1.
Perform the check for DTC except DTC P1610.
2.
Use CONSULT-III to erase DTC after fixing.
3.
Turn ignition switch OFF.
4.
Turn ignition switch ON when registered Intelligent Key is inserted into key slot and wait for 5 seconds.
5.
Return the ignition switch OFF and wait 5 seconds.
6.
Repeat steps 4 and 5 twice (total of 3 cycles).
7.
Check that engine can start when registered Intelligent Key insert into key slot.
>> INSPECTION END
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
P1610
LOCK MODE
When the starting operation is carried out
five or more times consecutively under the
following conditions.
• Unregistered Intelligent Key
• BCM or ECM is malfunctioning.
—
SEC-36
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
P1611 ID DISCORD, IMMU-ECM
P1611 ID DISCORD, IMMU-ECM
Description
INFOID:0000000005515483
BCM performs the ID verification with ECM that allows the engine to start. Start the engine if the ID is OK.
ECM prevents the engine from starting if the ID is not registered. BCM starts the communication with ECM if
ignition switch is turned ON.
DTC Logic
INFOID:0000000005515484
DTC DETECTION LOGIC
NOTE:
• If DTC B1611 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B1611 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005515485
1.
PERFORM INITIALIZATION
Perform initialization with CONSULT-III. Re-register all Intelligent Keys.
For initialization and registration of Intelligent Key. Refer to “CONSULT-III Operation Instruction NATS-IVIS/
NVIS”.
Can the system be initialized and can the engine be started with re-registered Intelligent Key?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-95, "Removal and Installation"
.
2.
Perform initialization with CONSULT-III.
For initialization, refer to “CONSULT-III Operation Instruction NATS-IVIS/NVIS”.
Can the system be initialized and can the engine be started with re-registered Intelligent Key?
YES
>> INSPECTION END
NO
>> GO TO 3.
3.
REPLACE ECM
1.
Replace ECM. Refer to
EC-16, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special
2.
Perform initialization with CONSULT-III.
Can the system be initialized and can the engine be started with re-registered Intelligent Key?
YES
>> INSPECTION END
NO
>> GO TO 4.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
P1611
ID DISCORD, IMMU-
ECM
The ID verification result between BCM and ECM is
NG. The registration is necessary.
• BCM
• ECM
P1611 ID DISCORD, IMMU-ECM
SEC-37
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
4.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
.
>> INSPECTION END
SEC-38
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
P1612 CHAIN OF ECM-IMMU
P1612 CHAIN OF ECM-IMMU
Description
INFOID:0000000005515486
BCM performs the ID verification with ECM that allows the engine to start. Start the engine if the ID is OK.
ECM prevents the engine from starting if the ID is not registered. BCM starts the communication with ECM if
ignition switch is turned ON.
DTC Logic
INFOID:0000000005515487
DTC DETECTION LOGIC
NOTE:
• If DTC P1612 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC P1612 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005515488
1.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-95, "Removal and Installation"
.
2.
Perform initialization with CONSULT-III.
For initialization, refer to “CONSULT-III Operation Instruction NATS-IVIS/NVIS”.
Does the engine start?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
REPLACE ECM
Replace ECM. Refer to
EC-16, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special
.
>> INSPECTION END
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
P1612
CHAIN OF ECM-IMMU
Inactive communication between ECM and BCM
• Harness or connectors
(The CAN communication line is open or
shorted)
• BCM
• ECM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст