Nissan Murano Z51. Instruction — part 1439
SHIFT LOCK SYSTEM
TM-107
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5.
CHECK HARNESS BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 1)
1.
Disconnect CVT shift selector connector.
2.
Check continuity between stop lamp switch vehicle side harness connector terminal and CVT shift selec-
tor vehicle side harness connector terminal.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace damaged parts.
6.
CHECK HARNESS BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 2)
Check continuity between control vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace damaged parts.
7.
CHECK GROUND CIRCUIT
Check continuity between CVT shift selector vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace damaged parts.
8.
CHECK CVT SHIFT SELECTOR
1.
Shift selector lever to “P” position.
2.
Check continuity between CVT shift selector connector terminals.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Replace CVT shift selector. Refer to
.
9.
CHECK SHIFT LOCK SOLENOID
1.
Remove shift lock unit. Refer to
2.
Check shift lock solenoid. Refer to
TM-108, "Component Inspection (Shift Lock Solenoid)"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace damaged parts.
Stop lamp switch vehicle side harness connector
CVT shift selector vehicle side harness connec-
tor
Continuity
Connector
Terminal
Connector
Terminal
E116
4
M57
6
Existed
CVT shift selector vehicle side harness connector
Ground
Continuity
Connector
Terminal
M57
6
Not existed
CVT shift selector vehicle side harness connector
Ground
Continuity
Connector
Terminal
M57
7
Existed
CVT shift selector connector
Continuity
Connector
Terminal
M57
6
7
Existed
TM-108
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F09B]
SHIFT LOCK SYSTEM
Component Inspection (Stop Lamp Switch)
INFOID:0000000005514070
1.
CHECK STOP LAMP SWITCH
Check continuity between stop lamp switch connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace stop lamp switch. Refer to
.
Component Inspection (Shift Lock relay)
INFOID:0000000005514071
1.
CHECK SHIFT LOCK RELAY
Apply voltage to terminals of shift lock relay connector to check the continuity.
CAUTION:
Connect the fuse between the terminals when applying the voltage.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace shift lock relay.
Component Inspection (Shift Lock Solenoid)
INFOID:0000000005514072
1.
CHECK SHIFT LOCK SOLENOID
Apply voltage to CVT shift selector connector terminals and then check that shift lock solenoid is activated.
CAUTION:
Connect the fuse between the terminals when applying the voltage.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace shift lock unit. Refer to
.
Stop lamp switch connector
Condition
Continuity
Connector
Terminal
E116
3
4
Depressed brake pedal
Existed
Released brake pedal
Not existed
Shift lock relay connector
Condition
Continuity
Connector
Terminal
E53
5
3
Apply 12 V direct voltage between terminals 2 and 1.
Existed
(+) (fuse)
(
−
)
Condition
Status
CVT shift selector connector
Connector
Terminal
M57
6
7
• Park switch: ON
• Apply 12 V direct current be-
tween terminals 6 and 7.
Shift lock solenoid operates
OVERDRIVE CONTROL SWITCH
TM-109
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OVERDRIVE CONTROL SWITCH
Description
INFOID:0000000005514073
• The Overdrive control switch is installed to the selector lever knob.
• When pushing the Overdrive control switch (OD OFF indicator lamp turns ON), the driving condition
becomes Overdrive OFF. When pushing again the Overdrive control switch (OD OFF indicator lamp turns
OFF), the driving condition changes to D range.
Component Function Check
INFOID:0000000005514074
1.
CHECK OVERDRIVE CONTROL SWITCH SIGNAL
1.
Turn ignition switch ON.
2.
Select “Data Monitor” in “TRANSMISSION”.
3.
Check the ON/OFF operations of monitor item.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Go to
Diagnosis Procedure
INFOID:0000000005514075
1.
CHECK CAN COMMUNICATION CIRCUIT
Perform “Self Diagnostic Results” in “TRANSMISSION”.
Is “U1000” indicated?
YES
>> Check CAN communication line. Refer to
NO
>> GO TO 2.
2.
CHECK COMBINATION METER
Perform “Self Diagnostic Results” in “METER/M&A”.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check DTC detected item. Refer to
3.
CHECK OVERDRIVE CONTROL SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect CVT shift selector connector.
3.
Check continuity overdrive control switch.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK GROUND CIRCUIT (PART 1)
Check continuity between CVT shift selector vehicle side harness connector terminal and ground.
Monitor item
Condition
Status
SPORT MODE SW
While pushing overdrive control switch
On
Other conditions
Off
CVT shift selector connector
Condition
Continuity
Connector
Terminal
M57
1
4
While pushing overdrive control switch
Existed
Other condition
Not existed
TM-110
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F09B]
OVERDRIVE CONTROL SWITCH
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace damaged parts.
5.
CHECK HARNESS BETWEEN CVT SHIFT SELECTOR AND COMBINATION METER (PART 1)
1.
Disconnect combination meter connector.
2.
Check continuity between CVT shift selector vehicle side harness connector terminal and combination
meter vehicle side harness connector terminal.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace damaged parts.
6.
CHECK HARNESS BETWEEN CVT SHIFT SELECTOR AND COMBINATION METER (STEP 2)
Check continuity between CVT shift selector vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace damaged parts.
7.
DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
NO
>> Repair or replace damaged parts.
CVT shift selector vehicle side harness connector
Ground
Continuity
Connector
Terminal
M57
4
Existed
CVT shift selector vehicle side harness connector
Combination meter vehicle side harness connector
Continuity
Connector
Terminal
Connector
Terminal
M57
1
M34
32
Existed
CVT shift selector vehicle side harness connector
Ground
Continuity
Connector
Terminal
M57
1
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст