Nissan Murano Z51. Instruction — part 1014
MIR-12
< DTC/CIRCUIT DIAGNOSIS >
[WITH ADP]
DOOR MIRROR REMOTE CONTROL SWITCH
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-210, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK MIRROR SWITCH
Check door mirror remote control switch (mirror switch).
Refer to
MIR-12, "MIRROR SWITCH : Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace door mirror remote control switch (mirror switch). Refer to
.
5.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-39, "Intermittent Incident"
>> INSPECTION END
MIRROR SWITCH : Component Inspection
INFOID:0000000005513404
1.
CHECK MIRROR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check continuity between door mirror remote control switch terminals.
Automatic drive positioner control unit Door
mirror
remote control switch
Continuity
Connector
Terminal
Connector
Terminal
M75
3
D14
15
Existed
4
13
15
12
16
4
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
3
Not existed
4
15
16
Door mirror remote control switch
Ground
Continuity
Connector
Terminal
D14
7
Existed
DOOR MIRROR REMOTE CONTROL SWITCH
MIR-13
< DTC/CIRCUIT DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror remote control switch. Refer to
MIR-75, "Removal and Installation"
CHANGEOVER SWITCH
CHANGEOVER SWITCH : Description
INFOID:0000000005513405
Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.
CHANGEOVER SWITCH : Component Function Check
INFOID:0000000005513406
1.
CHECK CHANGEOVER SWITCH FUNCTION
Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT-III.
Is the inspection result normal?
YES
>> Changeover switch function is OK.
NO
>> Refer to
MIR-13, "CHANGEOVER SWITCH : Diagnosis Procedure"
CHANGEOVER SWITCH : Diagnosis Procedure
INFOID:0000000005513407
1.
CHECK CHANGEOVER SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK CHANGEOVER SWITCH CIRCUIT
Door mirror remote control switch
Condition
Continuity
Connector
Terminal
D14
4
7
Mirror switch
RIGHT
Existed
Other than above
Not existed
13
LEFT
Existed
Other than above
Not existed
15
UP
Existed
Other than above
Not existed
12
DOWN
Existed
Other than above
Not existed
Monitor item
Condition
MIR CHNG SW-R/L
When operating the changeover toward the right or left side.
: ON
Other than above.
: OFF
(+)
(–)
Voltage (V)
(Approx.)
Door mirror remote control switch
Connector
Terminal
D14
10
Ground
5
11
MIR-14
< DTC/CIRCUIT DIAGNOSIS >
[WITH ADP]
DOOR MIRROR REMOTE CONTROL SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-210, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK CHANGEOVER SWITCH
Check door mirror remote control switch (changeover switch).
Refer to
MIR-14, "CHANGEOVER SWITCH : Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace door mirror remote control switch (changeover switch). Refer to
5.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-39, "Intermittent Incident"
>> INSPECTION END
CHANGEOVER SWITCH : Component Inspection
INFOID:0000000005513408
1.
CHECK CHANGEOVER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check continuity between door mirror remote control switch terminals.
Automatic drive positioner control unit Door
mirror
remote control switch
Continuity
Connector
Terminal
Connector
Terminal
M75
2
D14
11
Existed
14
10
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
2
Not existed
14
Door mirror remote control switch
Ground
Continuity
Connector
Terminal
D14
7
Existed
DOOR MIRROR REMOTE CONTROL SWITCH
MIR-15
< DTC/CIRCUIT DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror remote control switch. Refer to
MIR-75, "Removal and Installation"
Door mirror remote control switch
Condition
Continuity
Connector
Terminal
D14
10
7
Changeover switch
LEFT
Existed
Other than above
Not existed
11
RIGHT
Existed
Other than above
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст