Nissan Murano Z51. Instruction — part 817
GW-12
< REMOVAL AND INSTALLATION >
WINDSHIELD GLASS
REMOVAL AND INSTALLATION
WINDSHIELD GLASS
Exploded View
INFOID:0000000005513254
JMKIA1782GB
WINDSHIELD GLASS
GW-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Removal and Installation
INFOID:0000000005513255
REMOVAL
CAUTION:
Replace the windshield glass assembly with a new part after removal as it cannot be reused.
1.
Remove the front pillar garnish (LH/RH). Refer to
INT-20, "Removal and Installation"
.
2.
Remove partially the headlining (front edge). Refer to the following.
• For normal roof. Refer to
INT-27, "NORMAL ROOF : Removal and Installation"
• For sunroof. Refer to
INT-30, "SUNROOF : Removal and Installation"
.
3.
Remove the front wiper arms (LH/RH). Refer to
WW-130, "Removal and Installation"
4.
Remove the cowl top cover. Refer to
EXT-21, "Removal and Installation"
.
5.
Remove the roof side molding. Refer to
EXT-32, "SUNROOF : Removal and Installation"
6.
Remove glass using piano wire or power cutting tool (A) and an inflatable pump bag (B) after removing
moldings.
WARNING:
Always wear safety glasses and heavy gloves to prevent injury.
CAUTION:
• Be careful not to scratch the glass when removing.
• Never set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
• The dam rubber and insulator should be installed in position.
• Use a genuine Nissan Urethane Adhesive Kit (if available) or equivalent and follow the instructions provided
with it.
• Open a door window while the urethane adhesive is curing. This prevents the glass from being forced out by
passenger room air pressure when all door windows are closed.
• The molding must be installed securely so that it is in position and leaves no clearance.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive is completely
cured (approximately 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
1.
Windshield glass
2.
Fastener
3.
Windshield molding (side)
4.
Windshield molding (upper)
5.
Spacer
6.
Mirror base
7.
Rain sensor bracket
8.
Insulator
9.
Dam sealant rubber
10.
Roof
11.
Headlining ASSY
12. Adhesive
13.
Primer
14. Roof rail
15. Cowl top center
16.
Insulator dash lower
17. Body side outer
18. Front pillar garnish
19.
Cowl top cover
:Clip
Unit:
mm (in)
Note: • D and E on the exploded view are sections of sunroof models.
• The windshield glass, windshield molding upper, spacer, mirror base, rain sensor bracket, insulator and dam sealant rub-
ber constitute the windshield glass assembly.
Refer to
for symbols in the figure.
PIIB5779E
GW-14
< REMOVAL AND INSTALLATION >
WINDSHIELD GLASS
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Never let
them in contact with the skin and eyes.
• Use in an open, well ventilated location. Never breathe the vapors. They may be harmful if inhaled.
Move immediately to an area with fresh air if affected by vapor inhalation.
• Driving the vehicle before the urethane adhesive is completely cured may affect the performance of
the windshield in case of an accident.
CAUTION:
• Perform adjustment of front wiper arms stop location. Refer to
.
• Never use an adhesive which is past its usable term. Shelf life of this product is limited to six months
after the date of manufacture. Carefully adhere to the expiration or manufacture date printed on the
box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Never leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive is completely
cured. Curing time varies depending on temperature and humidity. The curing time increases under
lower temperature and lower humidity.
Inspection
INFOID:0000000005513256
REPAIRING WATER LEAKAGE FOR WINDSHIELD
Leakage can be repaired without removing the glass.
Determine the extent of leakage if water is leaking between the urethane adhesive material and body or glass.
This can be done by applying water to the windshield area while pushing glass outward.
Apply primer (if necessary) and then urethane adhesive to the leakage point to stop the leakage.
SIDE WINDOW GLASS
GW-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
SIDE WINDOW GLASS
Exploded View
INFOID:0000000005513257
Removal and Installation
INFOID:0000000005513258
REMOVAL
CAUTION:
Replace the side window glass with a new part after removal as it cannot be reused.
1.
Side window glass
2.
Adhesive
3.
Primer
4.
Body side outer panel
5.
Luggage side upper finisher
6.
Rear pillar inner
7.
Molding
8.
Spacer
: Clip
Unit:
mm (in)
Note: The side window glass, molding, spacer and clip constitute the side window glass assembly
Refer to
for symbols in the figure.
JMKIA3415GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст