Nissan Silvia. Instruction — part 74
Reverse Clutch Drum End Play
NMAT0170
Reverse clutch drum end play “T
2
”
0.55 - 0.90 mm (0.0217 - 0.0354 in)
Thickness of oil pump thrust washer
Thickness mm (in)
Part number*
0.9 (0.035)
1.1 (0.043)
1.3 (0.051)
1.5 (0.059)
1.7 (0.067)
1.9 (0.075)
31528-21X01
31528-21X02
31528-21X03
31528-21X04
31528-21X05
31528-21X06
*: Always check with the Parts Department for the latest parts information.
Removal and Installation
NMAT0171
Instruction control linkage
Number of returning revolutions for lock nut
2
Lock nut tightening torque
11 - 14 N·m
(1.1 - 1.5 kg-m, 8 - 10 ft-lb)
Distance between end of converter housing and torque converter
23.5 mm (0.925 in) or more
GI
MA
EM
LC
EC
FE
CL
MT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
SERVICE DATA AND SPECIFICATIONS (SDS)
Reverse Clutch Drum End Play
AT-293
NOTES
FRONT & REAR AXLE
CONTENTS
FRONT AXLE . . . . . . . . . . . . . . . . ..2
Precautions . . . . . . . . . . . . . . . . ..2
. . . . . . . . . . . . . . .2
Preparation . . . . . . . . . . . . . . . . ..2
. . . . . . . . . . 2
. . . . . . . . 2
Noise, Vibration and Harshness (NVH)
Troubleshooting . . . . . . . . . . . . . . ...3
. . . . . . . 3
On-vehicle Service. . . . . . . . . . . . . ...3
. . . . . . . . . . . . 3
. . . . . . . . . . .4
Wheel Hub and Knuckle. . . . . . . . . . . ..5
. . . . . . . . . . . . . . .5
. . . . . . . . . . . . . . . . .5
. . . . . . . . . . . . . . ..6
ABS Sensor Rotor . . . . . . . . . . . . . ...7
. . . . . . . . . . . . . . . . .7
. . . . . . . . . . . . . . ..7
Baffle Plate . . . . . . . . . . . . . . . . ..7
. . . . . . . . . . . . . . . . .7
. . . . . . . . . . . . . . ..7
Service Data and Specifications (SDS). . . . . ...8
. . . . . . . . . ...8
REAR AXLE. . . . . . . . . . . . . . . . . .9
Precautions . . . . . . . . . . . . . . . . ..9
. . . . . . . . . . . . . . .9
Preparation . . . . . . . . . . . . . . . . ..9
. . . . . . . . . . 9
. . . . . . . . 9
Noise, Vibration and Harshness (NVH)
Troubleshooting . . . . . . . . . . . . . . .10
On-vehicle Service. . . . . . . . . . . . . .10
. . . . . . . . . . .10
. . . . . . . . . . . . . . . 11
Wheel Hub and Axle Housing . . . . . . . . ... 11
. . . . . . . . . . . . . ... 11
. . . . . . . . . . . . . . . ... 11
. . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . 13
. . . . . . . . . . . . . . ...14
. . . . . . . . . . . . . . . .14
Drive Shaft . . . . . . . . . . . . . . . . .15
. . . . . . . . . . . . . ...15
. . . . . . . . . . . . . . . ...15
. . . . . . . . . . . . . . 15
. . . . . . . . . . . . . ...16
. . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . ...17
. . . . . . . . . . . . . . . .18
Service Data and Specifications (SDS). . . . . .20
. . . . . . . . . . . . . . .20
. . . . . . . . . ...20
GI
MA
EM
LC
EC
FE
CL
MT
AT
PD
SU
BR
ST
RS
BT
HA
SC
EL
IDX
SBR820B
Precautions
PRECAUTIONS
NMAX0001
I
When installing rubber parts, final tightening must be car-
ried out under unladen condition* with tires on ground.
*: Fuel, radiator coolant and engine oil full. Spare tire, jack,
hand tools and mats in designated positions.
I
After installing removed suspension parts, check wheel
alignment and adjust if necessary.
I
Use flare nut wrench when removing or installing brake
tubes.
I
Always torque brake lines when installing.
Preparation
SPECIAL SERVICE TOOLS
NMAX0002
Tool number
Tool name
Description
HT72520000
Ball joint remover
NT146
Removing tie-rod outer end and lower ball joint
GG94310000
Flare nut torque wrench
NT406
Removing and installing brake piping
a: 10 mm (0.39 in) dia.
COMMERCIAL SERVICE TOOLS
NMAX0003
Tool name
Description
1 Flare nut crowfoot
2 Torque wrench
NT360
Removing and installing each brake piping
a: 10 mm (0.39 in)
Baffle plate drift
NT065
Installing baffle plate
a: 88 mm (3.46 in) dia.
b: 68 mm (2.68 in) dia.
FRONT AXLE
Precautions
AX-2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст