Nissan Silvia. Instruction — part 176
Wiring Diagram
NMEC0797
TEC821
GI
MA
EM
LC
FE
CL
MT
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ELECTRICAL LOAD SIGNAL
Wiring Diagram
EC-219
Diagnostic Procedure
NMEC0798
1
INSPECTION START
Do you have CONSULT-II?
Yes or No
Yes
©
GO TO 2.
No
©
GO TO 4.
2
CHECK LOAD SIGNAL CIRCUIT OVERALL FUNCTION-I
With CONSULT-II
1. Turn ignition switch “ON”.
2. Check “LOAD SIGNAL” in “DATA MONITOR” mode with CONSULT-II under the following conditions.
SEC426C
OK or NG
OK
©
GO TO 3.
NG
©
GO TO 6.
3
CHECK LOAD SIGNAL CIRCUIT OVERALL FUNCTION-II
With CONSULT-II
1. Turn ignition switch “ON”.
2. Check “LOAD SIGNAL” in “DATA MONITOR” mode with CONSULT-II under the following conditions.
SEC427C
OK or NG
OK
©
INSPECTION END
NG
©
GO TO 9.
ELECTRICAL LOAD SIGNAL
Diagnostic Procedure
EC-220
4
CHECK LOAD SIGNAL CIRCUIT OVERALL FUNCTION-I
Without CONSULT-II
1. Turn ignition switch “ON”.
2. Check voltage between ECM terminal 33 and ground under the following conditions.
SEC428C
OK or NG
OK
©
GO TO 5.
NG
©
GO TO 6.
5
CHECK LOAD SIGNAL CIRCUIT OVERALL FUNCTION-II
Without CONSULT-II
1. Turn ignition switch “ON”.
2. Check voltage between ECM terminal 33 and ground under the following conditions.
SEC429C
OK or NG
OK
©
INSPECTION END
NG
©
GO TO 9.
6
CHECK REAR WINDOW DEFOGGER FUNCTION
1. Start engine.
2. Turn “ON” the rear window defogger switch.
3. Check the rear windshield. Is the rear windshield heated up?
Yes or No
Yes
©
GO TO 7.
No
©
Refer to EL-96, “Rear Window Defogger”.
GI
MA
EM
LC
FE
CL
MT
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ELECTRICAL LOAD SIGNAL
Diagnostic Procedure (Cont’d)
EC-221
7
CHECK REAR WINDOW DEFOGGER INPUT SIGNAL CIRCUIT
1. Stop engine
2. Disconnect ECM harness connector.
3. Disconnect rear window defogger relay.
4. Check harness continuity between ECM terminal 33 and rear window defogger relay terminals 5, 7 under the following
conditions.
SEC430C
5. Also check harness for short to ground and short to power.
OK or NG
OK
©
GO TO 12.
NG
©
GO TO 8.
8
DETECT MALFUNCTIONING PART
Check the following.
I
Harness connectors F4, M60
I
Harness connectors B3, M9
I
Joint connector 1
I
Harness open and short between ECM and rear window defogger relay
©
Repair open circuit or short to ground or short to power in harness or connectors.
9
CHECK HEADLAMP FUNCTION
1. Start engine.
2. Turn the lighting switch “2ND”.
3. Check that headlamps are illuminated.
Do the headlamps illuminate in both “High” and “Low” positions?
Yes or No
Yes
©
GO TO 10.
No
©
Refer to EL-28, “HEADLAMP”.
ELECTRICAL LOAD SIGNAL
Diagnostic Procedure (Cont’d)
EC-222
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст